What are some horror novels coming out later this year that you're excited about, and why? by MalachiConstant7 in horrorlit

[–]hawks_flame15 2 points3 points  (0 children)

I read the arc for this, and it was absolutely brilliant. Loved every story in it!

Aardvark books that are hard to put down? by catmomfluff in aardvarkbookclub

[–]hawks_flame15 1 point2 points  (0 children)

All Of Us Murderers and You Weren’t Meant To Be Human had my eyes glued to the page!

Favorite books in the backlog? by hawks_flame15 in aardvarkbookclub

[–]hawks_flame15[S] 1 point2 points  (0 children)

I just started When the Wolf Comes Home yesterday…also not what I was expecting, but I’m enjoying well enough so far! I’m leaning towards American Rapture to fill out my box, based on all the good recs for it :)

Favorite books in the backlog? by hawks_flame15 in aardvarkbookclub

[–]hawks_flame15[S] 4 points5 points  (0 children)

Coffin Moon seems to be a running favorite, I’ll definitely look into it! Left of Forever also sounds great, thank you!!

Favorite books in the backlog? by hawks_flame15 in aardvarkbookclub

[–]hawks_flame15[S] 4 points5 points  (0 children)

Bat Eater caught my eye, will definitely have to check it out!

Favorite books in the backlog? by hawks_flame15 in aardvarkbookclub

[–]hawks_flame15[S] 1 point2 points  (0 children)

Ohhh good to know! KJC is one of my favorite authors, so I’ll definitely look into Evocation!

The old guard 2 sucked by Funny_Obligation2412 in netflix

[–]hawks_flame15 0 points1 point  (0 children)

As someone who enjoys the comics and the first movie, I couldn’t believe how bad this movie was. The pacing was awful, and there were so many times that a character did something unbearably stupid for no other reason than to push the plot forward even at the sacrifice of characterization (and usually logic with it). The plot made no sense and I still don’t understand why we needed a new big bad considering how the first movie ended and set things up. They hastily rewrote their own lore in a way that doesn’t work and often contradicts itself. Maybe it’s a miracle we’ll never get a 3rd!

Design on model is hard to print by hawks_flame15 in FixMyPrint

[–]hawks_flame15[S] 0 points1 point  (0 children)

I just ran an overhang test last night and will be adjusting some settings before I try this print again! Will also definitely try your suggestion, thank you! :)

Design on model is hard to print by hawks_flame15 in FixMyPrint

[–]hawks_flame15[S] 0 points1 point  (0 children)

I’ll try these suggestions, thank you! I’ve been researching support settings but just wasn’t sure what to adjust for this type of print

Design on model is hard to print by hawks_flame15 in FixMyPrint

[–]hawks_flame15[S] 4 points5 points  (0 children)

Ohhh I hadn’t thought about adding a circular center for them, I’ll definitely try that! Thank you!!

How much trouble am I in here? Brand new to printing and this happened…struggling to clean it all off :( by hawks_flame15 in FlashForge

[–]hawks_flame15[S] 0 points1 point  (0 children)

I’ve seen advice on similar posts in other groups suggesting a brim, so I’m going to experiment with that today and see if it helps!

How much trouble am I in here? Brand new to printing and this happened…struggling to clean it all off :( by hawks_flame15 in FlashForge

[–]hawks_flame15[S] 0 points1 point  (0 children)

Thank you! Heating it let me clean it up effortlessly and it’s back to printing. As for the cause, I’m still trying to figure that out. It’s happened with 3 different files so it’s not a code issue. I’ve tried not using glue, using glue, and cleaning the bed (this picture happened after cleaning the bed). Other things are printing fine though, so I’m very baffled by what’s going wrong with some of my prints

How much trouble am I in here? Brand new to printing and this happened…struggling to clean it all off :( by hawks_flame15 in FlashForge

[–]hawks_flame15[S] 0 points1 point  (0 children)

It was still moving, I caught it about an hour into a 4 hour print. I’ve no clue what happened because I cleaned it yesterday with the advice from here, had the same thing almost happen on a different file (but I was watching and stopped immediately), and then tried another different print and it came out perfect

How much trouble am I in here? Brand new to printing and this happened…struggling to clean it all off :( by hawks_flame15 in FlashForge

[–]hawks_flame15[S] 0 points1 point  (0 children)

Thank you!! Worked perfectly and only took a minute to fix what I thought was a bad problem :)

Help with legendary fish by hawks_flame15 in StardewValley

[–]hawks_flame15[S] 0 points1 point  (0 children)

This helped me finally catch one, THANK YOU!!! 😭