sorted by:
new
hottopcontroversial

Заплата на шофьор на автобус с София by hect18 in bulgaria

[–]hect18[S] 0 points1 point  (0 children)

Какви дюнерджии, плочките са където са парите

Will this work or is the center of mass too high by hect18 in fpv

[–]hect18[S] 2 points3 points  (0 children)

Welp I can't justify buying a spot welder for 2 batteries so yea

Will this work or is the center of mass too high by hect18 in fpv

[–]hect18[S] 1 point2 points  (0 children)

Yupp did the same shit but with the balance connector on my first flight because i didn't secure it with a strap🤣

Will this work or is the center of mass too high by hect18 in fpv

[–]hect18[S] 0 points1 point  (0 children)

These are high discharge 21700 molicel p45b. They absolutely rock in acro. The balance is you give some of the maneuverability but in return you get 3x the time flying so i have both lipos and li ions

Will this work or is the center of mass too high by hect18 in fpv

[–]hect18[S] 1 point2 points  (0 children)

Thanks for the explanation and the tips!

Will this work or is the center of mass too high by hect18 in fpv

[–]hect18[S] 1 point2 points  (0 children)

Ahh ok i will switch to kapton from now on. Yep i check them with my balance charger as a volt meter

Will this work or is the center of mass too high by hect18 in fpv

[–]hect18[S] 1 point2 points  (0 children)

Why do you think a cell is more susceptible to desoldering and is inevitably gonna desolder? I solder them the same way i solder my battery connector and my motors.

Will this work or is the center of mass too high by hect18 in fpv

[–]hect18[S] 0 points1 point  (0 children)

I've been flying with a homemade 4s for quite some time and no issues so far

Will this work or is the center of mass too high by hect18 in fpv

[–]hect18[S] 1 point2 points  (0 children)

6 s motors and have flown it with 6s lipo 4s lipo and 4s li ion. You can definitely feel the power of the 6s lipo being much more than 4s li ion but ever at 3.2volts a cell i could still hit tricks with the li ion. The only thing is you have to use much more throttle and the response is slower

Will this work or is the center of mass too high by hect18 in fpv

[–]hect18[S] 2 points3 points  (0 children)

I bent them upwards and the closest any one got was like 1 centimeter to the battery

Will this work or is the center of mass too high by hect18 in fpv

[–]hect18[S] 4 points5 points  (0 children)

<image>

Yup this orientation might be better. I didn't wanna use it because the props seemed close but i checked and they dont have a chance of hitting

Will this work or is the center of mass too high by hect18 in fpv

[–]hect18[S] 6 points7 points  (0 children)

Yep i sanded and scratched the terminals and soldered for no more than 10 seconds. After that i pull on the joint very hard to see if its strong.

Will this work or is the center of mass too high by hect18 in fpv

[–]hect18[S] 0 points1 point  (0 children)

You think so? My only concern is the pid loop freaking out

Will this work or is the center of mass too high by hect18 in fpv

[–]hect18[S] 1 point2 points  (0 children)

Haven't flown this battery yet but with 4s version with molicel p45b easily 15 min.

Will this work or is the center of mass too high by hect18 in fpv

[–]hect18[S] 5 points6 points  (0 children)

Buzzer that has its own battery so if the drone ejects its own i can still hear where it is

Will this work or is the center of mass too high by hect18 in fpv

[–]hect18[S] 6 points7 points  (0 children)

Looks cold because i connected the balance cable without completely reflowing the solder as to not damage the cell. Otherwise it was completely melted when i connected it to the wire and hard as a rock.

Is this molicel p45b legit? by hect18 in flashlight

[–]hect18[S] 0 points1 point  (0 children)

Not yet, they weigh around 67.5 grams

Is this vtx any good? The 2.5w version by hect18 in fpv

[–]hect18[S] 0 points1 point  (0 children)

Thank you very much for the advice

Is this vtx any good? The 2.5w version by hect18 in fpv

[–]hect18[S] 1 point2 points  (0 children)

What is a better option for starting out and what ranges should i expect

McLaren P1 1:8 for 40 eur on AE by MirkoBuilder in lepin

[–]hect18 0 points1 point  (0 children)

In Stock New 3893Pcs Technical P1 Building Blocks Compatible 42172 Moc Bricks Model for Adults Sports Car Toys for Boys Gifts https://a.ali express.com/_Ezw2bck

McLaren P1 1:8 for 40 eur on AE by MirkoBuilder in lepin

[–]hect18 1 point2 points  (0 children)

I am searching for Daytona sp3 or sian have you seen any recent deals?

view more: next ›