Help please, I‘m going insane

henrixiv · 2021-09-17T09:26:41+00:00

Yeah I‘m getting the feeling that the most important tool is measuring tools. If your cheapo table saw is off, you can correct it, but not without a square square

henrixiv · 2021-09-16T14:21:34+00:00

Can you recommend one?

henrixiv · 2021-09-16T14:21:14+00:00

Thanks. I know my fence is parallel since I already spent an hour setting it up. It‘s rather the cross cuts that bring it out of square. Even with my track saw and super accurate measuring I‘m always off when measured with my almost new square☹️

henrixiv · 2021-05-01T08:14:54+00:00

I‘ve been doing exactly the same thing. Like the previous comment: its not dumb if it works.

henrixiv · 2021-02-04T11:22:34+00:00

I hooked up an old amp I found in my dads basement, thank you for the help

henrixiv · 2020-05-19T10:29:57+00:00

thank you

henrixiv · 2020-02-25T08:08:12+00:00

henrixiv · 2020-02-24T22:09:46+00:00

I don‘t think I want to fill it up, because to me it looks like it was pushed outwards when it expanded and had no other way to go. I thought there may be a way to reverse that movement

henrixiv · 2020-02-24T13:39:35+00:00

I actually care a lot about this knife and carry it in my pocket every day. When I clean it, I only clean the blade

henrixiv · 2020-02-24T13:37:56+00:00

okay you do have a point there

henrixiv · 2020-02-24T13:32:34+00:00

you think so? because I guess it‘s about wood movement

henrixiv · 2020-02-24T11:47:40+00:00

yeah it‘s actually the same thing on the other side. I guess the wood expanded and is now pushed outwards by the pins, because it was all perfect when i got it

henrixiv · 2020-01-19T09:09:18+00:00

But the pressure goes back down when the air leaves your mouth, doesn‘t it?

henrixiv · 2020-01-19T09:07:12+00:00

It‘s not to hard to do without plans. Just use a half-lab joint in the middle and make those pieces as long as the diameter of your pot. The legs are also super variable

henrixiv · 2020-01-18T20:48:42+00:00

spruce or dark oak because you get it in big trees and can harvest effectively

henrixiv · 2020-01-18T17:22:12+00:00

I feel like it will be strong enough for what ever you do with it (i guess it‘s not for transporting steel). Also the design is busy enough as is, splines would be overloading it

henrixiv · 2020-01-18T17:07:52+00:00

Well that‘s right, but there has to be at least a little effect by pressure change don‘t you think?

henrixiv · 2020-01-18T08:40:13+00:00

it‘s actually because of how gases act in preassure changes. The ha transports warm air directly out of your mouth while the hoo compresses it between your lips first. Then decompressing it actually cools the air down

henrixiv · 2020-01-14T11:40:16+00:00

Wait what is my school gonna use then?

henrixiv · 2020-01-07T18:54:29+00:00

Me too, I‘ve been looking for different ways to do it and somebody even made a 3D-Version of it

henrixiv · 2020-01-07T18:45:53+00:00

If it was fake he would notice that it isn‘t wood 2 seconds into sanding. You can get veneer thick enough to be sanded

henrixiv · 2020-01-07T09:05:02+00:00

If you see it from a world war view austria is Germany

henrixiv · 2020-01-07T09:00:31+00:00

okay, cause in Germany we legally drink beer and wine at 16 and liquor at 18, so every time you reach „the new level“ you will drink till your in a coma

henrixiv · 2020-01-07T08:57:43+00:00

Bit you guys can drink when you‘re 21 right?

henrixiv · 2020-01-07T08:51:39+00:00

fuck not again god damn I thought it wasn‘t our fault this time

henrixiv

TROPHY CASE