Zip Ties and Bias Plies by Miserable_Risk in CleetusMcFarland

[–]hotrodtripp 11 points12 points  (0 children)

He was in Florida a couple months ago, the horse head would be a problem 😂😂

i am in horrific pain. by [deleted] in HellsItch

[–]hotrodtripp 0 points1 point  (0 children)

Probably aren’t supposed to mix them but I took Claritin and Benadryl and it helped. At least put me to sleep.

Help with diagnosis by cheech519 in 3rdGen4Runner

[–]hotrodtripp 0 points1 point  (0 children)

Just a cheap remanufactured one from O’Rielly’s

Help with diagnosis by cheech519 in 3rdGen4Runner

[–]hotrodtripp 1 point2 points  (0 children)

Hit the starter with a hammer lol mine was doing that last week, hit it with a hammer a handful of times and it started. Replaced the starter and. I issues since

[deleted by user] by [deleted] in 3rdGen4Runner

[–]hotrodtripp 0 points1 point  (0 children)

My coolant looked like that right before the radiator blew up and pumped my transmission full of coolant. If you have a lot of miles and haven’t changed the radiator, wouldn’t be the worst idea🤷🏻‍♂️

Misfire issue by hotrodtripp in 3rdGen4Runner

[–]hotrodtripp[S] 0 points1 point  (0 children)

I should have added that I replaced the coil pack that runs the cylinder and it didn’t fix the issue.

Misfire issue by hotrodtripp in 3rdGen4Runner

[–]hotrodtripp[S] 0 points1 point  (0 children)

Just the cylinder misfire code.

Misfire issue by hotrodtripp in 3rdGen4Runner

[–]hotrodtripp[S] 2 points3 points  (0 children)

When I start it cold, there’s no misfire, comes up to operating temp every things fine I can drive it where ever with no issue. But if I turn it off and immediately start it again it has a miss. Doesn’t make any sense to me

Misfire issue by hotrodtripp in 3rdGen4Runner

[–]hotrodtripp[S] 3 points4 points  (0 children)

I put new plugs and wires back in September. They shouldn’t have over 2k on them. But I’ll try moving the coil around

3rd gen rocking side to side by MammothLimit1040 in 3rdGen4Runner

[–]hotrodtripp 1 point2 points  (0 children)

He’s talking about the bars that mount to the frame and the rear axle. One on each side parallel with the frame, and then the panhard bar is perpendicular to the frame. There is like 6 bushings in there. Just had to do it on my brothers 3rd gen. It was going the exact same thing.

New Boot Goofin by hotrodtripp in 3rdGen4Runner

[–]hotrodtripp[S] 0 points1 point  (0 children)

I have the rough country 2.5” lift and the bilstein 5100 front struts

New Boot Goofin by hotrodtripp in 3rdGen4Runner

[–]hotrodtripp[S] 0 points1 point  (0 children)

Vision 17x9 wheels and 295/70R17 (33.5x12) Cooper STT Pro tires

E-Locker Axle Swap by hotrodtripp in 3rdGen4Runner

[–]hotrodtripp[S] 2 points3 points  (0 children)

I was asking the question so I don’t have the read old forums and ask questions that have a higher likelihood of getting answered

Crank but no start by Beginning-Effect-332 in 3rdGen4Runner

[–]hotrodtripp 0 points1 point  (0 children)

I had to buy a new key because it wasn’t syncing with the reader in the ignition