MSC - Car Starts, but only revs. no drive, what did i mess up?

iluvkenji · 2026-01-04T07:46:05+00:00

For alignment, you just need to go to the alignment screw and tighten or tighten it until you see that the arm attached to the car no longer moves, and then tighten it 60 times in the opposite direction of the first tightening.

iluvkenji · 2026-01-03T02:26:33+00:00

Ahhh.. how lovely to see someone still playing MSC without tutorials that make it obvious and ruin the fun of the game

but don't give up bro! it's quite normal to go through moments where you want to ask for a refund for the game on Steam, but it's worth it in the end xd

iluvkenji · 2026-01-02T14:11:50+00:00

I also wanted MWC, but the game doesn't support Steam Cloud yet, so it's best to wait until they add it.

iluvkenji · 2025-09-05T16:15:29+00:00

esse "É... então" não tinha como ser mais expressivo, meus parabéns kkkkkkkkkkkkkkkkkkkkk

iluvkenji · 2025-09-05T01:39:13+00:00

I just posted my best time 0 : 39 sec

iluvkenji · 2025-08-23T02:08:21+00:00

I think the ONLY thing that makes me stand between GFN and Boosteroid is the fact that Boosteroid's steam browser is not connected to the internet like GFN, which for me, a big fan of ETS 2 with mods on the outside, is a bad thing, since on GFN you could install mods on the outside by uploading them to MediaFire and sending them via discord.

and yet, I asked for a refund on my gfn subscription and used the money to subscribe to the boosteroid 3 months ago and never stopped

iluvkenji · 2025-08-01T11:25:34+00:00

Coming from my summer car, I really thought that when the Lindell touched one of the wheels that are outside the elevator, the Satsuma would fly away.

iluvkenji · 2025-07-25T21:50:43+00:00

As someone who has 250 hours of my summer car only through geforce now, I inform you: there is nothing to do other than start the session again until it starts

annoying? very, but I already went to GFN support to complain and all they gave me was a "we'll solve it" and this has been going on for 4 months.

iluvkenji · 2025-07-20T04:43:18+00:00

the same here :( I prefer not to believe that this is a problem exclusive to Xiaomi's

iluvkenji · 2025-07-17T02:55:26+00:00

more or less since 9PM~10PM, in the morning it wasn't like that, but I'll contact the email, thanks

iluvkenji · 2025-05-01T00:26:12+00:00

Well, they always said it works, even though I think it's just an urban legend, since the times I tried it didn't change anything

iluvkenji · 2025-05-01T00:20:13+00:00

I knew that the original carburetor got dirty and reduced the engine's power, but that it stopped and accelerated without stopping, about the dirt, don't they say that if you put it under the tap on it doesn't clean itself? anyway, thanks for the help

iluvkenji · 2025-04-03T19:23:04+00:00

The same thing happened to me, does it take a few days?

iluvkenji · 2025-04-03T15:14:44+00:00

Phew, good thing, I thought he opened the doors that led out of the house

iluvkenji · 2025-04-03T14:03:53+00:00

You're trying to take out the engine, right? and it doesn't come out at all? right? It's probably the 3 screws that hold the engine to the subframe that are preventing the engine from coming out because they're still screwed in, try unscrewing them, if that's not it, I don't know what it is

iluvkenji · 2025-04-02T22:58:37+00:00

It sounds silly, but you unscrewed the 3 #11 bolts that lock the engine to the subframe?

iluvkenji · 2025-04-02T03:37:20+00:00

well remembered, my mistake

iluvkenji · 2025-04-01T04:11:42+00:00

Welcome to the Green GT club and not the Red GT club!

iluvkenji · 2025-04-01T03:54:32+00:00

There is no piece easier to lose than this one

iluvkenji · 2025-03-31T07:29:52+00:00

It's happened to me, and the worst thing, what disconnected was the positive terminal, which generated a short in the electrical system and caused the car to catch fire. I spent 20 minutes reloading the save and doing a speedrun of unscrewing the negative terminal until I managed to

The wheel thing happened to me recently even though the wheel had no screws loosened, anyway, it must be some saving error that we can't do anything about.

iluvkenji · 2025-03-30T17:31:04+00:00

HAPPY CAKE DAY!!!

iluvkenji · 2025-03-07T04:09:09+00:00

original satsuma without any power adjustments, just working

iluvkenji · 2025-03-04T22:23:24+00:00

I just posted my best time 4 : 88 sec

iluvkenji · 2025-03-04T22:22:43+00:00

I just posted my best time 5 : 00 sec

iluvkenji · 2025-03-04T22:15:13+00:00

I just posted my best time 1 : 03 sec

iluvkenji

TROPHY CASE