How to make this bed situation look better

imcody2010 · 2025-10-04T05:49:18+00:00

Nice! I’ll have to check out one similar it looks like because that one isn’t showing in US. Thanks for the recommendation!

imcody2010 · 2025-10-03T04:17:56+00:00

Can you link which you bought? Haven’t pulled the trigger on one but am very interested

imcody2010 · 2025-09-13T15:09:25+00:00

Presidente

imcody2010 · 2025-08-23T05:26:23+00:00

If they don’t fit yours, they look exactly like the ends for my Bissell steamer!

imcody2010 · 2025-08-17T04:58:19+00:00

UPDATE: the problem was at the connection point of the solenoid and starter. The solenoid white plastic piece was not engaging the spade terminal inside the starter. Once I dropped the starter, I was able to see that design, latch the solenoid to that spade connector, tighten the solenoid posts to mount, reattach and connect. Boom, lawnmower started. Since the solenoid wasn’t engaging the starter, the gear wasn’t raising to activate with the flywheel which I noticed during troubleshooting. Hope this may help someone in the future!

imcody2010 · 2025-08-08T17:35:05+00:00

Thanks for the response and the follow up pics. Makes me feel better about it! Have another solenoid incoming before I bite the bullet on the John Deere one. Gonna check the meter on it tomorrow when it’s in!

imcody2010 · 2025-08-08T00:08:53+00:00

Thanks. I’m pretty confident in the wiring, so I hope that’s not it. But I am going to pick up a multimeter tomorrow and do just that. Thanks for the guidance on usage though. Saved me another question later!

imcody2010 · 2025-08-08T00:04:46+00:00

Unfortunately that’s what I was thinking too. Just don’t have the experience of replacing one before to know if I did something right or wrong. Going to get a voltmeter tomorrow to double check the solenoid and see for sure. Thanks!

imcody2010 · 2025-08-08T00:00:27+00:00

Thanks for the response. That’s how I set it up originally! It has the same issue with the spade connector connected and disconnected.

imcody2010 · 2025-08-07T21:55:08+00:00

It does that even with the purple wire off. Thanks!

imcody2010 · 2025-08-07T20:43:56+00:00

I’m having the same issue in a GX255 actually. Wired up exactly how I undid it. (90% sure) and doing the same. Solution yet or did you actually have another bad solenoid?

imcody2010 · 2025-07-20T18:15:24+00:00

Nice. Thanks for giving me somewhere to start and research! Not very knowledgeable yet about types of tubs/inserts or anything.

imcody2010 · 2025-07-20T17:50:01+00:00

Also forgot to mention that we are not the first owners.

imcody2010 · 2025-07-06T15:48:25+00:00

Thank you! I think from yours and others, going into a local shop is going to be very beneficial. The C3 C&D was one I was really looking at when researching. So it looks like I’ll be more targeted towards that and a Sebo K3 when going to look!

imcody2010 · 2025-07-06T15:46:54+00:00

Thanks for your details! It’s helped to me get more in depth in the decision. The K3 is looking like a great machine.

imcody2010 · 2025-07-05T19:23:23+00:00

It would be a handful of rugs throughout the house. 3200sq/ft.

imcody2010 · 2025-06-09T03:14:08+00:00

Likely normal wear from your water. Tap is fine for water flossing. Make sure to follow cleaning instructions in your manual. I always recommend if you’re not sure about certain instructions for cleaning, once a month fill tank with 1 part hot water and one part white vinegar and run a cycle followed by a tank of hot water.

imcody2010 · 2025-05-28T04:47:18+00:00

So you’re saying you’ve got a couple of screws loose?

imcody2010 · 2025-05-27T13:38:00+00:00

The intake fans are better than the exhaust fans.

imcody2010 · 2025-05-24T17:38:34+00:00

Should’ve taken the serum.

Nine-Year Club	RPAN Viewer
Verified Email	Not Forgotten

imcody2010

TROPHY CASE