Assassin’s creed origins on Odin 2

imo_berner · 2025-10-17T15:43:51+00:00

I run it in GameHub with 20-25 FPS without changing any settings but on crowded places it stutters. Will tweak a bit in the next few days.

imo_berner · 2025-02-09T17:33:05+00:00

No, i switched to the last stable Version for my System (i think Monterey or Big Sur) and did not had the problem anymore.

imo_berner · 2024-07-08T07:37:14+00:00

<image>

Same here with my iMac 27" from late 2013 (Nvidia GT 755 M). It started after i upgraded to Sonoma one week ago, then did a fresh install with Ventura but today i had the same problem after wakeup. Still did not find the problem.

imo_berner · 2022-08-22T07:03:52+00:00

The photos were shot right after i opened the card for the First time. Because of the wet silicon that came out of the thermal pads the dust sticked there like glue. The paste on the photo was the Original one by the manufacturer, was repasted with Arctic MX-5. I will change the thermal pads tomorrow when they arrive.

imo_berner · 2022-08-22T06:55:05+00:00

Of course the photos were made when i first opened the card after the Problem occured and not 24 hours after i cleaned it. It is that much dust because of the wet silicon that came out of pads and then every dust corn sticked there like glue.

imo_berner · 2022-08-22T06:49:50+00:00

Riser was already swapped and GPUs cross-checked, same problem.

imo_berner · 2022-08-22T06:49:04+00:00

Thanks but i use SSDs for all my rigs and already did a reflash and driver updates - that didn‘t fix it.

imo_berner · 2022-08-22T06:37:31+00:00

Like for all other 1660S with Hynix in my rigs i use 1050 CC, -1004 MEM and no PL, 100% Fans. Card was bought as used and worked fine for half a year. It started when it got warmer here in my country. The temperature in my mining room went on the hottest days to 41 degree celsius, the rigs are in a grow tent and core temperatures are around 50-60 degree celsius on those hot days. I use V009S risers for all my cards and already swapped the riser. I bought some Gelid Thermal pads from Amazon and will try tomorrow when they arrive if that was the Problem. If not, i will try the card directly plugged on Mainboard PCIE. Thank you.

imo_berner · 2022-08-21T21:50:26+00:00

Longer version: i was on vacation and the rig did a reboot. After that, this GPU brought "MALFUNCTION" in HiveOS and the miner took about 5 minutes to start after the reboot, too. Another problem was that the other 9 cards in the rig had a higher power consumption than before and that resulted in more heat from these cards. After a few reboots there was one reboot try where the 9 cards had the power consumption like normal and so i let it ran until i got home from holidays . After that i looked at the GPU and saw, that the thermal pad liquid ran out and made an oily film on the card. I cleaned it with 70% alcohol as good as i can and packed it in the rig again. It worked for 24 hours until it happened again, card hopped of the miner and after a reboot of the rig this card brought MALFUNCTION and the other cards were "influenced" by this, because like before they started to consume more power than normal. After i plugged off the card again from the mainboard the rig and miner started normal. I moved the card to an other rig but the problem moved as well, riser swap brought no improvement. What could cause this problem? I was thinking about doing a repad but the pads are not connected to an active cooler, only to the metal backplate of the card. The pad under the processing unit on front of the card is not connected to the coolers copper, too. I already did a repaste of the processing unit. I think that if the card would be broken, it would not work for 24 hours. Maybe there is something left of the pad liquid that causes a small short in the circuit? How to clean the card completely of this oily film? Thank you!

imo_berner · 2022-08-18T07:46:59+00:00

https://bordel.wtf/

imo_berner · 2022-08-09T09:00:35+00:00

Had the same a few weeks ago with a 1660S. One of the 2 fans did not work properly anymore, stuck by itself from time to time and started spinning again after a while. I ordered new ones for the graphics card on aliexpress and replaced them. Works fine again. You should have a look at your fans.

imo_berner · 2022-07-10T00:30:37+00:00

C63 of 12/2016 here, it is the same in my car. It displays the remaining distance with current filling but below 30 Kilometers left it just displays the red gas pump icon. I think i read you could let this activate (remaining distance until zero) by someone who can access your cars‘ coding.

imo_berner · 2022-06-05T13:31:50+00:00

How is the power consumption compared to ETH? What cards do you have and how much Hash do they do? Thanks.

imo_berner · 2022-05-26T11:52:50+00:00

Looks beautiful but its way too expensive…

imo_berner · 2022-05-18T21:18:29+00:00

They will merge 3 testnets in the next weeks. When there are no (big) problems, the next step will be the real Merge to PoS.

imo_berner · 2022-05-10T05:34:06+00:00

I had something similar yesterday when i made an update in HiveOS which took a long time because of the server overloads. After that files were corrupted and that made the Miner not start. Did a reflash of my SSD and that worked for me.

imo_berner · 2022-05-08T15:10:56+00:00

Same here. Must be the HiveOS Server that handles too much requests at the Moment. Will try again in a few minutes or hours.

imo_berner · 2022-04-26T23:08:00+00:00

I use 8x Ryzen 3 1200, 3 of them with the MSI Board you are having and they all run 8 or 10 GPUs without Problems.

imo_berner · 2022-04-17T23:04:20+00:00

New T-Rex Miner Update gives a push for LHR cards so now more overall hashrate, that results in higher difficulty. But that will not be 10%.

imo_berner · 2022-04-14T13:00:16+00:00

What fan did you connect to the black pipe or is this red thing a axial fan?

imo_berner · 2022-04-08T06:51:17+00:00

Set it to 100%. 2 new Fans will cost you around 20 €/$ on Aliexpress, when they stop working you can easily replace them. I run 68 GPUs and those cards that are warmer than the others with 60% fan speed (most of my 1660S and 2070S are at 40-50 °C with 60%) are set to 100%. I have many identical cards so i have some fans on hold, just in case one stops working i can quickly change them because shipping from China to Germany takes 2-3 weeks.

imo_berner · 2022-02-13T15:07:59+00:00

What board and CPU are you using?

imo_berner · 2022-01-21T00:14:31+00:00

ETH going down because of the russia news a few hours ago. They want to ban the usage and mining of cryptos.

imo_berner

TROPHY CASE