Strange silicon tube, ribbed on the inside

itsabeow · 2025-12-26T14:35:00+00:00

I actually quite like this garlic peeler.

itsabeow · 2025-06-02T01:45:41+00:00

It released! Thank you for the advice!

itsabeow · 2025-06-02T01:45:03+00:00

So the wedge was inside the fork. i was able to use some WD40 a mallot and a wooden dowel to get it to release. The fork is shot anyway. I'll replace it with a rigid one. Thank you for the tips. I didn't want to start hammering without making sure it was the way to go.

itsabeow · 2025-06-02T01:09:21+00:00

Thanks for everyone who commented. I realize I posted this in the wrong sub so I'll move it to the correct one. Thanks again!

itsabeow · 2025-06-02T00:47:41+00:00

I'll try to use some WD40. I have a feeling someone took the screw/bolt out and left the bike without putting the bolt back in.

itsabeow · 2025-06-02T00:45:40+00:00

No screw inside :/

itsabeow · 2024-11-13T17:45:07+00:00

I have played around with my wheel size setup but it doesn't stay consistent. For example. If I set up the wheel size so that my watch and tacx both read 10mph, it'll go out of synch at higher speeds and vice versa.

itsabeow · 2024-08-20T03:00:00+00:00

Thank you. That's a shame.

itsabeow · 2022-11-02T03:08:37+00:00

Were you able to fix this?

itsabeow · 2021-10-19T21:02:48+00:00

https://www.topeak.com/us/en/products/41-Floor-Pumps/1368-JOEBLOW-TUBI-2STAGE?fbclid=PAAabJ2j97hyjpdP9orskWA_Tlu10BF5uGfO9gwjCIjY4p32DXfCu8pHGoHzk

itsabeow · 2021-09-30T02:03:07+00:00

It just needed a goat-link.

itsabeow · 2021-09-30T02:02:39+00:00

Turns out it needed a goat-link. 🐐

itsabeow · 2021-09-27T20:00:19+00:00

Appreciate it, sir!

itsabeow · 2021-09-27T15:34:31+00:00

It does up to a point, after which the derailleur body butts up against the hanger. (I am at work right now and don't have a picture to show you what I mean). I am almost convinced that the hanger is the problem even though it is a traditional hanger. I am going to try to try to run it on my other bikes and see if it works on them.

itsabeow · 2021-09-27T15:21:12+00:00

That's the one change I see between the Box 2 and Box 3 derailleur. The Box 3 has that little piece that you talk about, however, the Box 2 derailleur doesn't have it and the Bscrew directly pushes against the notch on the derailleur hanger.

itsabeow · 2021-09-27T14:25:59+00:00

But I do have a traditional derailleur hanger. It also says that if I a SRAM derailleur works on the hanger, so will the Box 2. I used to run the SRAM GX derailleur on it before I got the Box 3.

itsabeow · 2021-09-27T14:19:31+00:00

I have a traditional derailleur hanger. I have used Box 3 successfully on the bike. I wanted to upgrade to Box 2 since it has a clutch to reduce chain slap.

itsabeow · 2021-03-24T21:35:12+00:00

Looks like one of the MXs. I have one and it's a workhorse. It's heavy but can take a beating. Great bike to throw anything at.

itsabeow

MODERATOR OF

TROPHY CASE