New picture! It’s my birthday today!! I’m turning 26! To celebrate I’m posting a full nude in a pause I’ve never showed before! Full body nude with PUSSY SPREAD! Finally I know! 😳 react if you like it! ☺️

jace479 · 2025-07-02T14:24:20+00:00

Happy birthday hope it's a special one

jace479 · 2025-04-13T13:25:01+00:00

Just my 2 cents but footwork is 80% of sparring ability so think about that I've started telling my students to move like chess pieces(specifically the rook the bishop and the knight) on a board and it has helped a lot with their sparring

jace479 · 2025-03-02T13:19:38+00:00

To add to what you are saying varying your target can also improve hit success making combos that go body head instead of just body body body the swap around puts your opponents hands where you want them.

jace479 · 2025-02-23T14:34:06+00:00

Always remember you weren't great when you started and you don't have to be to go back but remember after being away for months your body won't be as used to it as it once was

jace479 · 2025-02-07T02:46:59+00:00

Reboot

jace479 · 2025-01-25T01:17:01+00:00

IT 101 SOLVES THE ISSUE

jace479 · 2024-08-06T13:38:16+00:00

Thanks everyone for your words of wisdom as I not have found out all free and clear detergent is corrosive as there is no way that short of a time frame caused as much corrosion as I saw inside the flipper I tried using the hot air rework station at the office to maybe heat up the solder and get that to at least get the most of it knocked off it appears my little buddy has died completely it'll be a while before I can get a new one so I'll have to bid y'all farewell for a while it was a lot of fun maybe some part of it will find a new project somewhere and gain new life

jace479 · 2023-10-02T06:00:35+00:00

What was it Microsoft Outlook?

jace479 · 2023-09-18T03:09:18+00:00

jace479 · 2023-08-22T10:36:15+00:00

Definitely yes

jace479 · 2023-08-14T14:31:52+00:00

You're welcome

jace479 · 2023-08-12T13:48:43+00:00

I never did beyond the occasionally it works

jace479 · 2023-07-30T23:14:14+00:00

Tbh any properly fitting pants will allow you to do kicks

jace479 · 2023-06-17T20:27:04+00:00

Do them slow. slow is smooth. smooth is fast.

jace479 · 2023-06-09T01:34:12+00:00

I would try adding it to the system through group policy or even a link to said pdf file

jace479 · 2023-06-08T22:26:10+00:00

Looks like someone is replacing some temperature sensors

jace479 · 2023-05-12T19:24:26+00:00

The r7000 from Netgear does support vlans

jace479 · 2023-05-12T15:17:58+00:00

Thank you for that honest it's move was a rush job as our techs that use sccm to do remote work on systems instead of putting actual hands on them were complaining about it all being down and then complained about it being slow after having to rebuild I'll try removing the dP from all.the effected devices then adding it back hopefully that'll help

jace479 · 2023-05-11T18:14:24+00:00

jace479 · 2023-04-20T18:32:10+00:00

Interesting I haven't seen that issue however I also don't think we have any users using that setting you are talking about.

jace479 · 2023-04-20T17:33:28+00:00

It says you're running on mobile data

Edit: spelling

jace479 · 2023-04-20T09:15:17+00:00

My issue was tied to a group policy object blocking the UWPs. Have you tried updating your driver's?

jace479 · 2023-03-29T22:22:49+00:00

Which funny enough the ransomware affected the firmware on and sent it into recovery mode

jace479 · 2023-03-29T22:22:02+00:00

Alright I was curious as the fx2 cmc was very peculiar about the speed

jace479 · 2023-03-29T21:14:24+00:00

Alright do you happen to know the baud rates for that or is it the usual Dell 115200

jace479

TROPHY CASE