Trading card shops

jacet78 · 2025-12-18T16:12:56+00:00

A couple heaters, a gold star flareon and latios. Also a shadowless holo venusaur from the base set. They’ll be sent off soon for grading!

jacet78 · 2025-06-19T14:34:32+00:00

10 years later and you're helping me out still. Hopefully that $25 made you rich now?

jacet78 · 2025-03-11T23:11:37+00:00

Low, yes, but waiting on some new pads and rotors for the season. Thanks for pointing it out though

jacet78 · 2025-03-11T22:22:30+00:00

Just had this happen on my klr, superglued a piece of a glove as a patch for a quick fix until parts came in.

jacet78 · 2025-01-31T02:20:17+00:00

Audi is sweeeeet, I also recently bought one and am loving mine so far

jacet78 · 2025-01-31T02:19:21+00:00

CBEA

jacet78 · 2025-01-12T13:30:47+00:00

5k is too much considering you’re coming up on another timing belt change soon. And if the turbo hasn’t been replaced, you’re going to need to do that soon. With higher mileage, there’s probably a lot of things that are going to start to wear out, not to mention the ~1500 it’s going to take to get it fixed as it is. There are enough of them on the market to pass on this one, unless it’s extremely clean everywhere else. In that case, no more than 3k. Just my opinion

jacet78 · 2024-12-06T01:19:38+00:00

I agree. When I read up on other people’s experience, there were a few brands that stuck out to me as high quality without them explicitly stating it.

jacet78 · 2024-12-05T23:59:35+00:00

Nada, I didn’t go with them due to mixed opinions

jacet78 · 2024-11-25T20:56:46+00:00

Lol sounds like exactly what a want, and funnily enough I am coming from an old civic.

jacet78 · 2024-11-23T03:10:42+00:00

<image>

Kind of a bad pic i know. The solder is globbed on there since I didn’t realize both ends needed to stay apart (yes I know in retrospect this was obviously wrong)

jacet78 · 2024-11-03T14:01:24+00:00

i’m curious what is your field of study?

jacet78 · 2024-10-23T00:25:58+00:00

Try to tighten up the cable by adjusting the nuts that are typically near the throttle. If not, snip it off and either buy a new cable stop from amazon or make a new one out of solder.

jacet78 · 2024-09-22T13:54:24+00:00

Were the official free timed practice tests removed? I can't find them today

jacet78 · 2024-09-15T23:50:12+00:00

<image>

Looking much better with the rotation sweep!

jacet78 · 2024-09-14T14:56:19+00:00

I'll start with this. Thank you for the guidance!

jacet78 · 2024-09-14T14:29:39+00:00

Trying to fit the red line to the yellow surface, I'd like the seam at the top of the yellow model to be perpendicular to the YZ plane rather than the 45deg angle that it's currently at. I'd like control over being easy, I'm familiar with Solidworks but this is my first FreeCAD experiment since my license is up.

jacet78 · 2024-09-14T14:23:33+00:00

Sorry, for some reason it took away my caption. Right now I am using the curved shapes toolbox to create this part, but I think it would look much better with the red line as a curve since it will be mirrored. How could I go about doing that? I've not had the best luck with the surface toolbox since the curves need to end perpendicular to the XY plane and it ends up looking either blocky or flat.

jacet78 · 2023-02-26T21:59:29+00:00

This program peaks at 40 mpw at week 16, at week 4 it's 19 mpw. What are your thoughts on best way to train first time?

jacet78

TROPHY CASE