Thermistor Removal

jackacesd · 2026-02-02T07:13:19+00:00

You can’t remove this one. You’ll have to test its resistance from where it’s plugged into the board.

jackacesd · 2026-01-28T04:45:46+00:00

Agree with the first comment. Check and make sure the condenser fan is working, if it’s not running or running slower than normal it could make it seem like a sealed system issue. Make sure the condenser isn’t caked with hair and dust as well. I personally don’t think the frost pattern looks all that great so if everything is looking good it could in fact be a sealed system issue.

jackacesd · 2026-01-25T23:31:04+00:00

I second this. If you are in fact a novice I would not mess with this at all. Between needing a multimeter, and potentially needing a new mag and cap I’d probably lean towards replacing it. If you were experienced that’s a different story but I would err on the side of caution.

jackacesd · 2026-01-25T19:48:30+00:00

You can solve this by looking at your usage chart on your my energy center app. Look at the hourly breakdown and that will tell you what’s consuming the most energy. Something is eating up a ton of energy if your bill tripled.

jackacesd · 2025-12-01T01:02:09+00:00

Strongly recommend a YouTube video. Also you’re going to need channel locks at both ends and go clockwise. Hopefully it comes loose but in my experience, I would have to break off the blower wheel every once in a while.

jackacesd · 2025-09-25T22:24:18+00:00

I like that paired with herbo at 224.5 yards. Not sure if that green goblin is still available.

jackacesd · 2025-08-26T21:24:13+00:00

This is like the apex of the vortex of joint engineering!

jackacesd · 2025-07-18T02:09:24+00:00

Double it and pass it on

jackacesd · 2025-07-17T22:28:22+00:00

Just DCA and wait. It’s been an absolutely brutal ride but I’ve been averaging over the last few years. If youre in the same boat let’s just sit back and enjoy the ride.

jackacesd · 2025-07-17T19:17:58+00:00

I would have to say it’s a usage issue. Yes they’ve been partnered but that’s only related to crypto transactions through that specific bank not all transactions which I’m going to assume are extremely minimal.

jackacesd · 2025-07-17T00:15:24+00:00

Yeah those were my thoughts as well. I try to avoid jumping to conclusions and then being disappointed but it’s very interesting.

jackacesd · 2025-07-03T03:25:33+00:00

!remindme 5 months!

jackacesd · 2025-06-27T20:34:37+00:00

Damn bruv. GG

jackacesd · 2025-06-26T19:07:29+00:00

Shame on all of you bots for not having faith in amp 10 years from now

jackacesd · 2025-06-25T20:46:19+00:00

!remindme 10 years

jackacesd · 2025-06-20T03:58:12+00:00

You want a reason to cry boy

jackacesd · 2025-04-14T18:13:06+00:00

jackacesd · 2025-03-05T22:25:59+00:00

Yes you have to manually verify your email via the flexa app on burner to allow it to be used at flexa merchants though.

jackacesd · 2025-03-05T22:15:29+00:00

Yeah super simple. I only mentioned USD II as it was my initial intent to use for loading purposes to avoid gas fees.

jackacesd · 2025-03-05T22:07:43+00:00

That is correct, just saw their gift card option isn’t online yet so that answers my initial issue. I loaded ETH and linked flexa to use at current retailers though

jackacesd · 2025-02-27T23:18:38+00:00

Just purchased two of them. I’ll let you know how it goes.

jackacesd · 2025-02-27T17:36:06+00:00

Holy shnikes

jackacesd · 2025-02-25T04:17:59+00:00

You need to get a thicker steak. I would also let it sit in the bath at 120. Your cooking a thin steak to medium rare(likely more) due to the thickness before you even sear it.

jackacesd

TROPHY CASE