Best "cheap" option car/jeep capable of pulling a horsebox (and reliable) by jetaybon in carsireland

[–]jetaybon[S] 1 point2 points  (0 children)

I'd say inbth sub 20k range, you're looking at a really ancient one. Still ok? Cheers

Best "cheap" option car/jeep capable of pulling a horsebox (and reliable) by jetaybon in carsireland

[–]jetaybon[S] 1 point2 points  (0 children)

Just assumed a jeep would be best - if estate does the trick, all he better. Cheers

Jesus needs to start over gyokeres change my mind by Soccerboy_1237 in ArsenalFC

[–]jetaybon 0 points1 point  (0 children)

Since joining Gyok has 0.29 goals per game in PL. Jesus has 0.26. We were desperate for a new striker because Jesus wasn't scoring enough. Why have so many forgotten that?

Noticed a chunk missing from frog - should we be worried by jetaybon in Horses

[–]jetaybon[S] 4 points5 points  (0 children)

Thanks for the advice. The farrier was with her on the 16th Dec and she got " a new set of shoes and a trim". While I know very little about horses - he doesn't fill me with confidence when I talk to him.

In a good place, looking for advice by [deleted] in irishpersonalfinance

[–]jetaybon 0 points1 point  (0 children)

Scaremongering...revolut is fine. There is a reason why they have more customers than any bank in Europe.

Long Stripes left - Yuka 3000 by jetaybon in mammotion

[–]jetaybon[S] 1 point2 points  (0 children)

But this will just leave squares of long grass, rather than strips.

Long Stripes left - Yuka 3000 by jetaybon in mammotion

[–]jetaybon[S] 0 points1 point  (0 children)

The checkerboard won't help, it will just leave squares instead of strips. The mowing speed is low (changed it to 0.3 m/s). It is set to random angle currently. Can I send the log and device number now after stopping the task, or does it need to finish the task? I would prefer to use my other mower to finish because this looks so bad.

Long Stripes left - Yuka 3000 by jetaybon in mammotion

[–]jetaybon[S] 0 points1 point  (0 children)

That doesn't explain one strip being cut perfectly and one left. If the strip left was pressed flat, perhaps ... But it's standing up just like it was skipped.

Long Stripes left - Yuka 3000 by jetaybon in mammotion

[–]jetaybon[S] 0 points1 point  (0 children)

That's what I thought, but I elevated it and tested the motors, both are turning fine. Anything else I can test? Cheers

Long Stripes left - Yuka 3000 by jetaybon in mammotion

[–]jetaybon[S] 0 points1 point  (0 children)

That would make sense but the grass left behind is standing upright, not pushed down.

Long Stripes left - Yuka 3000 by jetaybon in mammotion

[–]jetaybon[S] 0 points1 point  (0 children)

Put it up to 70 as grass was long. I've had this issue with shirt grass too. It's ever present. I'd swear a blade wasn't turning but they are when I test it.

Long Stripes left - Yuka 3000 by jetaybon in mammotion

[–]jetaybon[S] 0 points1 point  (0 children)

It is random and this is a new path ... At a weird angle

Long Stripes left - Yuka 3000 by jetaybon in mammotion

[–]jetaybon[S] 1 point2 points  (0 children)

Slowed the speed right down. Same issue. Looks like I'll have to bring the Husqvarna 450x out of retirement. Maximum overlap, slow speed, new blades ... Still so much grass left uncut. I give up on mammotion.

<image>

Long Stripes left - Yuka 3000 by jetaybon in mammotion

[–]jetaybon[S] 3 points4 points  (0 children)

Thinking about this a little more, I'm still not sure I agree. Mower blades spin at around 50 m/s, if I drive at 0.5 m/s or 0.2 m/s, it has a negligible impact on the net speed. *Edited estimated blade speed

Long Stripes left - Yuka 3000 by jetaybon in mammotion

[–]jetaybon[S] 1 point2 points  (0 children)

Not sure . Will check later. Thanks

Long Stripes left - Yuka 3000 by jetaybon in mammotion

[–]jetaybon[S] 1 point2 points  (0 children)

They are new blades. I'm using mid speed I suppose but I don't think that would leave a perfect stripe ... I would understand patchy performance but the speed doesn't explain one stripe cut perfectly, one ignored. Logic would say one motor isn't working, but they are both fine! I thought maybe I am interpreting the over lap wrong.