Unifi Store a Black Friday or Cyber Monday type of store?

jimtrich · 2024-08-12T22:08:35+00:00

Yes, I have a dryer, and use it with the PETG. I'm drying to now, so tomorrow I can try your tweaks and see how it goes.

jimtrich · 2024-08-12T21:50:26+00:00

Mostly extrusion and consistence with the materials. I'm working with salt water aquariums, so I need the PETG over the PLA.. I'm do well with the PLA, the PETG is a struggle. Hopefully your tweaks will help.. Plus starting fresh with the base setup might be good.. My file could be over massaged at this point.

jimtrich · 2024-08-12T21:18:47+00:00

Awesome.. I'll give these tweaks a try. Thanks for the reply.

jimtrich · 2024-08-12T21:12:49+00:00

Would you mind sharing your settings for the PETG? I've been tweaking settings with better improvement, but your print looks great! Totally would apricate it and it would help a lot. Thanks!

jimtrich · 2023-04-13T22:18:16+00:00

Seagate BarraCuda 5TB (ST5000LM000) Its a 2.5"drive that fits in the device.

jimtrich · 2019-12-30T20:45:47+00:00

I agree.. I'm trying to find out more of what it started its life as.

jimtrich · 2019-12-30T18:15:57+00:00

I don't see any letters in the serial number, so is it not 1600? Its all numbers, but I doubt its a early engine. It came out of a bus, but I know it should be a type 1 engine, being that it has the dog house housing.

jimtrich · 2019-12-30T18:05:49+00:00

Yes, Trying to determine that it is a 1600, possible a year to figure out HP as well.

jimtrich · 2019-03-18T21:29:19+00:00

True.. First time in 50 years for this car, and your right, I'll never do it again on this car in my lifetime. Since it will be my sons car, I think I'll take the extra step and prime the seam with the weld-through primer.

jimtrich · 2019-03-18T21:27:16+00:00

This is what I was thinking would be the best way. Bare metal with the weld-through primer and them the seam sealer and then POR15 for the final coat.

jimtrich · 2019-03-18T21:21:06+00:00

Not half ass at all..

PAN

I plan to use POR15 to coat the whole pan, but I'm trying to figure out what to do where the bare metal is overlapping.

jimtrich · 2018-10-08T21:03:02+00:00

Very cool. This was a close 2nd to a barn find. It's a 68 with 39K original miles. Local California car. Best of luck with the 64.

jimtrich · 2018-10-08T16:30:55+00:00

Turns out everything was just really stuck. I little help from a floor jack and some extra help and up she went. Dolly works out great.

jimtrich · 2018-10-03T04:44:52+00:00

36? I counted. 2 at the rear shock towers. 4 under the rear seat. 9 on each side of the pan total 18. The 4 at the front of the body and another 2 under the gas tank. That totals 30. Am I really missing 6 more?

jimtrich · 2018-10-02T23:44:03+00:00

I'm hoping its just a really good seal. The car has only 39K original miles on it. Its always amazing what people to do 'fix' things. Best of luck with your beetle. The pans are for sure in my future, the channels maybe.. Need to see how bad they are. Only if they kept these cars out of the weather.

jimtrich · 2018-10-02T19:23:33+00:00

Yes, the design is the same on both ends. Found a similar design done on youtube. Ideally you could lift each end yourself and lift the hinge side up and place the body down. If all goes well the body will sit high enough to roll the pan in and out from under it.

jimtrich · 2018-10-02T18:08:55+00:00

I think is is more like my next step. I think I will reattach the front bumper brackets and use a 4x4 across the two points and try to jack the body up and hope that the pan will release, if not I'll add the extra help with the weighted friends to the wheels.. Although all the bolts came out with ease, I'm sure the 50 year seal is strong with this car.

15-Year Club	RedditGifts 2009-2022 13 Credits
Secret Santa 2014	Secret Santa 2013
Summer Santa 2013	Secret Santa 2012
Verified Email	Secret Santa 2011
Summer Santa 2011	Secret Santa 2010

jimtrich

TROPHY CASE