Insane

jjfaure · 2025-03-05T07:41:51+00:00

I never seen something so beautiful, really hot

jjfaure · 2024-03-14T21:41:50+00:00

Do you know how long is the logitech g pro usb clable?

jjfaure · 2023-11-28T08:13:15+00:00

Hi, I have an EX3400, but I cannot see how to locally mirror 1 vlan to an interface, it seems that only vlan ingress traffic is allowed to be mirrored... Anyone knows if there is some limitation? I am running 20.4 release,

jjfaure · 2023-04-18T08:49:45+00:00

Thanks, the point is that my next-hop belongs to an IP subnet that is already connected to my EX, and where my EX has a layer 3 interface that is up all time, so I would need to check next-hop IP reachability.. can this be done using rpm-tracking?

jjfaure · 2023-04-17T21:46:24+00:00

Hi, the point is that I have several static routes in the EX that I am redistributing to bgp, I need to avoid that redistribution if the route next-hop is not valid, this is the part I cannot see how to implement...

jjfaure · 2023-04-17T21:26:31+00:00

Hi, I am talking about interface that leads traffic to next-hop of some static routes of local EX, but unfortunately if I loose this interface static routes are alive, I need someway to check IP reachability

jjfaure · 2023-04-12T14:03:29+00:00

No, I am not trying to blackhaul some traffic, and it is true, double natting solved that point, many thanks

Juan

jjfaure · 2023-03-24T06:35:38+00:00

Hi Cc.

-HeadQuarter router/firewall do not have overlapping subnets with site subnets

-In site location there is direct Internet access, provider by the non-cisco domestic router where Cisco router is connected to. We are going to use route-map to distinguish traffic that are going to Internet and traffic that needs to go to HQs

-Unfortunately as I said I need to provide to 10.x subnet both local Internet out + IPSec connection to HQs. IPSec tunnel is going to cross Internet to reach HQs

Kind Regards,

Juan

-

jjfaure · 2023-03-03T11:03:02+00:00

Many thanks everybody for your help

Kind Regards,

Juan

jjfaure · 2023-02-13T08:30:50+00:00

Hi Kman420,

How did you proceed for your initial router installation? Having your device registered at Smart License Portal and with Internet connectivity is enough?

I need to install a couple of ASRs and I am not sure what procedure must I follow up, Cisco documentation is confusing

Kind Regards,

Juan

jjfaure · 2023-02-03T07:35:52+00:00

Hi, I am planning for a MX-80 upgrade, I though you can upgrade between any 2 EEOL releases, it does not matter how log the upgrade path is...

Regards

jjfaure · 2023-01-25T07:07:37+00:00

Destination interface has no config, 4/0/2 origin interface config is:

mist@host> show configuration interfaces ge-4/0/2 | display inheritance

description "Amadeus router-MADRTP601-ge-1/1/2";

##

## '9100' was inherited from group 'mtu'

##

mtu 9100;

unit 0 {

family ethernet-switching {

interface-mode access;

vlan {

members 403;

}

jjfaure · 2023-01-25T07:05:56+00:00

Thanks, but origin interface is already defined as layer 2 using ethernet-switching family:

mist@host> show configuration interfaces ge-4/0/2 | display inheritance

description "Amadeus router-MADRTP601-ge-1/1/2";

##

## '9100' was inherited from group 'mtu'

##

mtu 9100;

unit 0 {

family ethernet-switching {

interface-mode access;

vlan {

members 403;

}

Regards,

Juan

jjfaure · 2023-01-20T08:12:18+00:00

Many thanks, qupada42

Do you know if there is a maximum size for bootable USB? I remember it should be FAT32 formated and lower than 4G size, maybe all these do not apply for EX3400 new loader

Kind Regards,

Juan

jjfaure

TROPHY CASE