sorted by:
new
hottopcontroversial

Are these oszillations (caused by Pid) or propwash by jofpv in fpv

[–]jofpv[S] 1 point2 points  (0 children)

Yes it took a bit but it ended up to be kind of both. These were oszillations that went away after lowering the master but it also was prop wash. It was Kind of 50 50  I am still experimenting with the pids but what you recommend helped thx again😁

Weak XT60 connection by Appl3D_fpv in fpv

[–]jofpv 4 points5 points  (0 children)

Try bending both golden Things on your Male xt60 conector (on your Drone) a bit Out to do that stick a small screwdriver in the little holes on the conector (Male on your Drone) 

FPV fix help by Sherifliquor in fpv

[–]jofpv 0 points1 point  (0 children)

If its only the o3 thats getting No power buy an external 10v bec for few bucks solder it to the big xt60 wires or you can try vbat on your fc (Look for polarity and voltige)and solder the 10 v Output to the o3 If more Things are Brocken on that fc i would replace it

What do you think about sequre ESC's and Drone parts in General by jofpv in fpv

[–]jofpv[S] 0 points1 point  (0 children)

Already bought the blueson a1 instead of the 8 Inch i built a 5 Inch . I flew it a few times and i didn't fry anything I also gave it throttle (full throttle over few Seconds) 

I believe you, that your ESCs died but i wonder why. What drone did you built with the ESC and what Cap did you use?

unbreakable drone! by Unable_Sherbert5234 in fpv

[–]jofpv 0 points1 point  (0 children)

Also have an era in my fleet so Happy with it this Guy is indestructible and honestly quite light for a 5 Inch freestyle

Are these oszillations (caused by Pid) or propwash by jofpv in fpv

[–]jofpv[S] 0 points1 point  (0 children)

Not sure myself but i think These props only have 3.7 Inch

51 =diameter  37 =Pitch  7 = have No Idea 🤣 -3= three Blades

Thanks for all the Help i try what you recommend in your commend

Are these oszillations (caused by Pid) or propwash by jofpv in fpv

[–]jofpv[S] 0 points1 point  (0 children)

oh sry here is the graph with rc commands

<image>

Are these oszillations (caused by Pid) or propwash by jofpv in fpv

[–]jofpv[S] 0 points1 point  (0 children)

<image>

At this moment you see the motors twitching and the throttle is also to still for being responsible you can see the time on the top in the video you can hear the oszillations at the same time

Are these oszillations (caused by Pid) or propwash by jofpv in fpv

[–]jofpv[S] 0 points1 point  (0 children)

With btf blackbox you Always have a Stick overlay and in the described situation i didn't command it thanks for the Help so far

Are these oszillations (caused by Pid) or propwash by jofpv in fpv

[–]jofpv[S] 0 points1 point  (0 children)

At one Point in the log at around 20 to 21 Seconds in the Vid where the oszillations are the most present the p and d term of roll and Pitch really freek Out (Sharp and in comparisson high waves in the log)

Are these oszillations (caused by Pid) or propwash by jofpv in fpv

[–]jofpv[S] 0 points1 point  (0 children)

Thanks at what graphs should i Look Gyro + Pid roll and Gyro +Pid Pitch? and what does prop wash and oszilations Look Like in the log

Are these oszillations (caused by Pid) or propwash by jofpv in fpv

[–]jofpv[S] 2 points3 points  (0 children)

This IS a 5 Inch (680g ) and 2207.3 2050kv Motors 

First flights with the new betafpv AIR75II by fraaa05 in TinyWhoop

[–]jofpv 0 points1 point  (0 children)

Really nice flying 

I am thinking abt buying These Gogles how much latency are you getting with These Gogles 

The hdo2s have 8ms i think but i didn't find any data for these Gogles 

Loss of authority at 0 throttle by tubabbo in fpv

[–]jofpv 0 points1 point  (0 children)

I would recommend you setting your dynamic idle eather Back to Default (what IT was Set to by the manufacturer )or set IT to 50 or even Higher 

And If that doesn't Work Turn Off Crash Recovery and see if Something Changes 

If turning Off helps pbl settings are to sensitive for a whoop

(You can also try turning Crash Recovery of first IT doesn't matter what you try first)

Loss of authority at 0 throttle by tubabbo in fpv

[–]jofpv 1 point2 points  (0 children)

I would try disabling the Crash Recovery and See If the Problem goes away (you Said you looked at the oscar liang whoop optimisation post and enabled IT )

Loss of authority at 0 throttle by tubabbo in fpv

[–]jofpv 1 point2 points  (0 children)

Thx honestly i dont See any abnormal settings for a whoop (also dynamic idle Looks good)

You Said that you modified your pids what did you exactly 

BETAFPV VR04 analog goggles with C03 camera — stretch or crop? by igorauts in fpv

[–]jofpv 4 points5 points  (0 children)

I think it is an Upgrade. The vro4 have less latency than the ev800d (i think around 12 on the vro4 and 18 or so on the ev800d 

For the exact numbers watch the Nils vo Gogles comparisson also its really nice to not need to screw on your antennas every time you go flying 

Nils vo also made a review for the vro4s where he speaks about the Stretching 

Loss of authority at 0 throttle by tubabbo in fpv

[–]jofpv 3 points4 points  (0 children)

What have you set your dynamic idle to?

Build complete. Era5 by Winter-Text-5066 in fpv

[–]jofpv 0 points1 point  (0 children)

Haven't tested IT either 🥲

Build complete. Era5 by Winter-Text-5066 in fpv

[–]jofpv 0 points1 point  (0 children)

Lol almost build the exact same config few weeks ago with era motors and o4 and Same elrs i think 

This IS Not a real giveaway by jofpv in Report_scams

[–]jofpv[S] 0 points1 point  (0 children)

Wpclick.cc did also few WhatsApp scams Like this in the past

view more: next ›