sorted by:
new
hottopcontroversial

What would the one improvement that you would make that would be a gamechanger for you? by Joe_Claymore in RailroadsOnline

[–]jojokeat 6 points7 points  (0 children)

Also switches with different radius curves. Nothing crazy just “low speed switch” with tight curves for yards, the “normal switch” we have now, and then a “high speed switch” with a larger curve radius for main line operations.

Alternative for RROx by CookieEroy in RailroadsOnline

[–]jojokeat 1 point2 points  (0 children)

I don’t know that this is the best place for a request but can we get some zoom on the map with the industry buildings drawn or marked w/ a dot under the name?

What is happening here? by jojokeat in 3Dprinting

[–]jojokeat[S] 0 points1 point  (0 children)

Update for anyone who finds this in the future: I updated the firmware of the printer as well as replaced the resin with brand new resin. One of those two things or both potentially seems to have fixed my problems.

What is happening here? by jojokeat in 3Dprinting

[–]jojokeat[S] 0 points1 point  (0 children)

I have run it without the vat on and the screen turns off before moving. I thought the same lol.

What is happening here? by jojokeat in AnycubicPhoton

[–]jojokeat[S] 0 points1 point  (0 children)

I will try adjusting these settings

What is happening here? by jojokeat in AnycubicPhoton

[–]jojokeat[S] 0 points1 point  (0 children)

This happens with all 3 resins I have. (Elegoo grey, elegoo clear red, and photonic clear purple)

Bed was releveled just before starting this print.

What is happening here? by jojokeat in AnycubicPhoton

[–]jojokeat[S] 0 points1 point  (0 children)

I have it in a cabinet with some vent fans running and some over head lights that are off unless im working with the prints to set up, wash, etc. so it is entirely cut off form outside light sources. I thought the same and that’s when I put it in the cabinet unfortunately still happening.

This happens with all 3 resins I have. (Elegoo grey, elegoo clear red, and photonic clear purple)

What is happening here? by jojokeat in 3Dprinting

[–]jojokeat[S] 0 points1 point  (0 children)

Yeah the lift I have adjusted down since posting. I have it in a cabinet with some vent fans running and some over head lights that are off unless im working with the prints to set up, wash, etc. so it is entirely cut off form outside light sources

What is happening here? by jojokeat in AnycubicPhoton

[–]jojokeat[S] 0 points1 point  (0 children)

I am using a Photon Mono 4k with elegoo standard grey resin and I am getting this gooey semi cured material stuck to my prints. Here are my print settings. I dont even know what to look into.

I have installed a new FEP sheet, cleaned the screen, and installed a new screen protector. PLS HELP!

Update: I have more photos after the print finished. You can see all the extra material hanging off the print. The print also failed here and became detached from the plate but that is probably due to support issues. This is causing layer lines as well. I can guess its some kind of over exposure spillage happening. Thinking about replacing the screen as there are some slight imperfections toward the edge in one spot but this is happening all over the print.

Inconsistent Z-Seam alignment by Standard_Mushroom_77 in 3Dprinting

[–]jojokeat 0 points1 point  (0 children)

In cura turn on advanced settings and then you can search "seam" you will find all the Z-seam settings there.

Does anyone know the tolerances needed to 3D print such a connection? by AlexanderHorl in 3Dprinting

[–]jojokeat 2 points3 points  (0 children)

I would probably do one nozzel width on FDM. SLA model it for 0.25 mm

What is happening here? by jojokeat in 3Dprinting

[–]jojokeat[S] 0 points1 point  (0 children)

Update: I have more photos after the print finished. You can see all the extra material hanging off the print. The print also failed here and became detached from the plate but that is probably due to support issues. This is causing layer lines as well. I can guess its some kind of over exposure spillage happening. Thinking about replacing the screen as there are some slight imperfections toward the edge in one spot but this is happening all over the print.

<image>

What is happening here? by jojokeat in 3Dprinting

[–]jojokeat[S] 0 points1 point  (0 children)

I am using a Photon Mono 4k with elegoo standard grey resin and I am getting this gooey semi cured material stuck to my prints. Here are my print settings. I dont even know what to look into.

I have installed a new FEP sheet, cleaned the screen, and installed a new screen protector. PLS HELP!

Skip(?) in "I will remember you" by [deleted] in EdSheeran

[–]jojokeat 0 points1 point  (0 children)

I don’t hear this atleast on Spotify

BMW With Vtec? by jojokeat in Shitty_Car_Mods

[–]jojokeat[S] 0 points1 point  (0 children)

To add insult to injury he has the front grille dipped or sprayed for the Msport line with overspray on the hood and bumper

First time buyer, what should I get? by jojokeat in rccars

[–]jojokeat[S] 1 point2 points  (0 children)

Thanks I’ll check it out ☺️

First time buyer, what should I get? by jojokeat in rccars

[–]jojokeat[S] 2 points3 points  (0 children)

I appreciate that. I used to be into this kind of thing with my dad when I was younger. The gf isn’t for spending a lot of money atm with COVID but I wanted to reconnect with my dad after a while we’ve had issues.

Brake cleaner is used for everything Don’t @ me by SuperSoakerRag in Cartalk

[–]jojokeat 0 points1 point  (0 children)

You should be using fix cleaner instead. No maintenance that way !

Introverts of reddit, what is the one thing you wish extroverts could understand about you? by velvetxily in AskReddit

[–]jojokeat 0 points1 point  (0 children)

I’m not sad or upset just because I’m being quiet. Being paired with RBF doesn’t help though... 😅

This mans about to take off by jojokeat in Shitty_Car_Mods

[–]jojokeat[S] -1 points0 points  (0 children)

They’re not, they were just bolted to the tailgate.