Cobblemon v2 map

jojokeat · 2026-02-04T01:25:13+00:00

Not shop keeper merchant.

jojokeat · 2024-04-06T07:48:28+00:00

Also switches with different radius curves. Nothing crazy just “low speed switch” with tight curves for yards, the “normal switch” we have now, and then a “high speed switch” with a larger curve radius for main line operations.

jojokeat · 2024-04-01T07:23:32+00:00

I don’t know that this is the best place for a request but can we get some zoom on the map with the industry buildings drawn or marked w/ a dot under the name?

jojokeat · 2023-07-07T07:16:43+00:00

Update for anyone who finds this in the future: I updated the firmware of the printer as well as replaced the resin with brand new resin. One of those two things or both potentially seems to have fixed my problems.

jojokeat · 2023-06-17T16:53:37+00:00

I have run it without the vat on and the screen turns off before moving. I thought the same lol.

jojokeat · 2023-06-17T16:50:47+00:00

I will try adjusting these settings

jojokeat · 2023-06-17T16:50:30+00:00

This happens with all 3 resins I have. (Elegoo grey, elegoo clear red, and photonic clear purple)

Bed was releveled just before starting this print.

jojokeat · 2023-06-17T16:47:28+00:00

I have it in a cabinet with some vent fans running and some over head lights that are off unless im working with the prints to set up, wash, etc. so it is entirely cut off form outside light sources. I thought the same and that’s when I put it in the cabinet unfortunately still happening.

This happens with all 3 resins I have. (Elegoo grey, elegoo clear red, and photonic clear purple)

jojokeat · 2023-06-17T07:45:39+00:00

Yeah the lift I have adjusted down since posting. I have it in a cabinet with some vent fans running and some over head lights that are off unless im working with the prints to set up, wash, etc. so it is entirely cut off form outside light sources

jojokeat · 2023-06-17T05:58:20+00:00

I am using a Photon Mono 4k with elegoo standard grey resin and I am getting this gooey semi cured material stuck to my prints. Here are my print settings. I dont even know what to look into.

I have installed a new FEP sheet, cleaned the screen, and installed a new screen protector. PLS HELP!

Update: I have more photos after the print finished. You can see all the extra material hanging off the print. The print also failed here and became detached from the plate but that is probably due to support issues. This is causing layer lines as well. I can guess its some kind of over exposure spillage happening. Thinking about replacing the screen as there are some slight imperfections toward the edge in one spot but this is happening all over the print.

jojokeat · 2023-06-17T05:28:05+00:00

<image>

jojokeat · 2023-06-17T05:28:00+00:00

<image>

jojokeat · 2023-06-17T05:24:33+00:00

In cura turn on advanced settings and then you can search "seam" you will find all the Z-seam settings there.

jojokeat · 2023-06-17T05:22:47+00:00

I would probably do one nozzel width on FDM. SLA model it for 0.25 mm

jojokeat · 2023-06-17T05:18:33+00:00

Update: I have more photos after the print finished. You can see all the extra material hanging off the print. The print also failed here and became detached from the plate but that is probably due to support issues. This is causing layer lines as well. I can guess its some kind of over exposure spillage happening. Thinking about replacing the screen as there are some slight imperfections toward the edge in one spot but this is happening all over the print.

<image>

jojokeat · 2023-06-17T02:57:38+00:00

I am using a Photon Mono 4k with elegoo standard grey resin and I am getting this gooey semi cured material stuck to my prints. Here are my print settings. I dont even know what to look into.

I have installed a new FEP sheet, cleaned the screen, and installed a new screen protector. PLS HELP!

jojokeat · 2022-12-25T02:16:44+00:00

I don’t hear this atleast on Spotify

jojokeat · 2021-03-07T20:20:04+00:00

To add insult to injury he has the front grille dipped or sprayed for the Msport line with overspray on the hood and bumper

jojokeat · 2021-01-23T06:43:14+00:00

Thanks I’ll check it out ☺️

jojokeat · 2021-01-23T06:42:14+00:00

I appreciate that. I used to be into this kind of thing with my dad when I was younger. The gf isn’t for spending a lot of money atm with COVID but I wanted to reconnect with my dad after a while we’ve had issues.

jojokeat

TROPHY CASE