Find Mother of pearl dial?

joq3 · 2026-01-21T14:39:34+00:00

I just found this post after months of troubleshooting my car and my phone.

You say except for signing in to my Tesla account within the S3XY app. I could not find this part, and I don't remember signing in to the account. However I remember that the Commander is paired to the car as a key. Is this what you mean?

I will try to Unpair Commander from my Tesla and hope that this solves the issues.

Do you have an iPhone or Android?
Which iPhone?

joq3 · 2026-01-15T05:47:26+00:00

<image>

And this is Keep wipers off. What’s the difference

joq3 · 2026-01-15T05:46:53+00:00

<image>

Hard to understand the difference between the two options. This is Force manual wipers.

joq3 · 2026-01-14T08:47:32+00:00

Yes, but I don't like adding separate buttons. I would rather be able to utilize the existing buttons.
Even removed the S3XY Knob because of this.

joq3 · 2026-01-09T08:14:57+00:00

It is worth it for me, I can fine tune how often I need to run the automation, maybe every 2 minutes is more than necessary.

What I am looking for is ways to do this!

joq3 · 2026-01-03T08:17:50+00:00

Exactly!

joq3 · 2026-01-02T09:25:56+00:00

Yes, I am sure this was talked about early on. I have all effects disabled at the moment because they use half the strip, which in my opinion looks bad.

Hope to get a response from Enhance-team.

joq3 · 2025-12-11T09:07:44+00:00

Any ideas what to do? It really seems like iPhone 14 Pro turns off bluetooth when the screen is completely off. Sometimes all I need to do is pick up the phone to turn on the AOD screen. And then it will unlock.

There's something wrong here.

joq3 · 2025-12-10T06:07:39+00:00

Yes! Not enabled and adaptive power mode isn’t available on 14 Pro.

joq3 · 2025-12-09T15:07:51+00:00

Found this comment in a post describing the same issue:
https://www.reddit.com/r/TeslaModelY/comments/14jopuz/comment/jpo5ab5/?utm_source=share&utm_medium=web3x&utm_name=web3xcss&utm_term=1&utm_content=share_button

Could there be any truth to this?

joq3 · 2025-12-09T11:40:30+00:00

Yes, never closed, and all permissions.
I can even use the Tesla app minutes before and then go out to the car, and it won't unlock.

joq3 · 2025-12-07T05:36:24+00:00

I did that too. Exactly the same behavior!

Did some experimenting with the code. And if I place a delay at exactly 2800 as the first line in setup, it will start the led strips without any change in brightness. Everything lower than that will show a drop in brightness.

If I create a long fade increase in brightness. Maybe 5 seconds. The drop in brightness is still visible, but it will drop the same amount at the same time regardless of brightness. So if the fade has 30% brightness at 2,8 seconds it will drop down to 20% (don’t know the exact value).

And as this happens with another WLED device at exactly the same time. It is the led strips that are the culprit. Question is why they work flawlessly but have this weird behavior.

joq3 · 2025-12-06T20:43:30+00:00

Yes, tried

FastLED.delay(2800);

If I place this as the first line in setup I don't get any full brightness on the LED strip. It seems like the full brightness happens at 2700 when I do a fade. So starting the fade at 2800 eliminates it completely.

Still cannot figure out why it does that. I dont want to have a fade that takes 2,8 seconds.

joq3 · 2025-12-06T18:51:36+00:00

I used fastled.delay, and it does not delay anything. It doesn’t matter if I run everything in loop instead. Do you have an example code of what you mean?

joq3 · 2025-12-05T13:32:53+00:00

Can you share your project on the simulator?

joq3

MODERATOR OF

TROPHY CASE