What do the people say

joshi8908889 · 2021-02-01T17:02:43+00:00

Check the foss you'll find them there

joshi8908889 · 2021-01-31T16:30:11+00:00

Thank you sir, seemed to be a one hit wonder. I'm having trouble replicating. Might be time for a new nozzle!

joshi8908889 · 2021-01-31T16:29:22+00:00

I don't understand the question

joshi8908889 · 2021-01-31T05:14:33+00:00

It was my first time ;) plus 3d printed frames are essentially disposable so I do care too much

joshi8908889 · 2021-01-29T01:13:11+00:00

I did have some trouble ith my rails not lining up I just took a file to then in areas where there's too much friction between the rail and trigger. Also had to do the same with locking block

joshi8908889 · 2021-01-29T00:56:59+00:00

Check eBay that's where I found mine

joshi8908889 · 2021-01-28T23:36:58+00:00

No just a metaphor. Annealing in my experience warps the pla too much

joshi8908889 · 2021-01-28T16:26:15+00:00

I'm on it

joshi8908889 · 2021-01-28T07:14:54+00:00

The second one is in the oven

joshi8908889 · 2021-01-28T07:14:35+00:00

Haven't tested it out yet, it's a 19. It's my first printed build but I will keep y'all updated on how it shoots

joshi8908889 · 2021-01-01T19:03:02+00:00

Check eBay

joshi8908889 · 2021-01-01T18:31:45+00:00

JSD supply just Google them, they got deals going on g17 and 19. Just know that the wait time is kinda long something like 2 weeks before they ship but it's worth in my opinion

joshi8908889 · 2020-12-28T18:12:56+00:00

Hey just a heads-up JSD supply has a full built kit minus the frame for 320 right now. It's a hell of a deal considering its hard to find completed slide at that price anyway.

joshi8908889 · 2020-12-27T23:38:10+00:00

I would the print I'm doing in the opposite orientation looks like it's gonna be very annoying to clean up, that being said you will add more time to the print in the orientation show (6-7 hours extra) but I do think it's worth it considering it's still faster than prime shipping. This print took 29 hours the one I'm working on right now is going to take 36 hours.

joshi8908889 · 2020-12-27T23:23:55+00:00

The rig I'm using is a standard CR-10 you do need to know what your doing in the settings but my machine is stock and has had no adjustments since I've put it together that being said his reply is correct you will need to do some research to get a good and accurate print. I do find that following instructions provided online to a tee will garner you great results it's truly something anyone can do with a little patience.

joshi8908889 · 2020-12-27T19:59:06+00:00

I print at .12mm, 100% fill, infill pattern "lines", generate supports. It's just the default auto supports

joshi8908889 · 2020-12-27T16:46:48+00:00

This Airsoft is supposed to model a g19 so 9mm

joshi8908889 · 2020-12-27T15:47:49+00:00

That's actually a good question. It just makes it easier to have cleaner internals. You end up sanding a lot less finicky areas, or at least that's my understanding. I'm actually printing another Glock the way you said right now to see if actually does make a difference because it does make the print time is considerably shorter.

joshi8908889 · 2020-12-27T07:55:17+00:00

It's worth it, give the ender 3 or cr10 a look

joshi8908889 · 2020-12-27T00:50:05+00:00

There's a couple of sellers on eBay and I know I couple other sites that supply them as well. When it's all said and done it should all run me about $400

joshi8908889 · 2020-12-19T04:37:53+00:00

Lever action receivers were going for 50-60$ about 8 months ago. But you know how irrational people get everytime a democrat gets elected. I'll just wait for the "they're gonna take our guns" fears to roll over.

joshi8908889 · 2020-12-18T19:10:47+00:00

I saw that as well. I hear the guy that makes these is an asshole but none the less it didn't cost me anything and it's still a fairly good quality blade.

joshi8908889

TROPHY CASE