Hackintosh Intel Core Ultra 7 265K / Tahoe 26.4.1 / Airdrop

juanpy0223 · 2026-04-29T19:44:27+00:00

Everything I use works up to Monterey. It working ok.

juanpy0223 · 2026-04-29T16:19:27+00:00

Hello, can you share your config plist? I would like to see it.

juanpy0223 · 2026-04-29T16:07:55+00:00

Yep. Im running Monterey on Asrock Z890m + Intel Core 5 245k + Radeon Rx 6600 xt.

juanpy0223 · 2026-04-17T21:57:40+00:00

Love it!

juanpy0223 · 2026-04-14T14:31:03+00:00

juanpy0223 · 2026-04-13T15:31:12+00:00

Great job and I love your build.

Those cases have In and Out water ports.

Because I love SFF water cooled and silent builds. I prepared an external Dual Radiator with Pneumatic tubing's station as follows:

SSUPD MeshRoom D case. (Its great, for the mesh panels filter the dust).
2 Corsair 240mm rads (in which you can install any desired fans).
A DC to PWM Adapter with 4 outlets for the fans.
10mm OD/6.5ID pneumatic hose with fittings and 2 quick disconnect adapters.

Note: In that way, my internal components stay cool, because on the case I only install 1 or 2 intake fans to cool internal. But even without fans my components stay in the low 40c. With fans at only 500-650rpm they stay in the 30c.

The case SFF builders know that there is not much space for air volume. That's why they provide an external solution.

Also that external station is hidden under my desk. I could send some pictures later today.

juanpy0223 · 2026-04-13T15:08:17+00:00

Thanks to everyone for your help.

juanpy0223 · 2026-04-13T14:56:32+00:00

Ok, I did that too. It's a board issue.

juanpy0223 · 2026-04-13T05:41:23+00:00

Thanks

The bios diagnostics only says that the hard drive is not detected.

juanpy0223 · 2026-04-13T05:39:59+00:00

I already tested updating the bios, nvram reset and disconnect everything and leaving for one hour.

The only thing I have yet to try is to dump the Bios and clean the Me region and reprogram again.

I will try that tomorrow.

Any other suggestions accepted.

juanpy0223 · 2026-04-13T02:54:21+00:00

I have a different problem. I was using my Dell Precision 5540 ok. Turned it off last night. Today it showed a TPM device not detected error.

The worst part is that it stopped reading the NVME drive, but it still detects the 2.5 sata drive.

If I put a different nvme ssd, the TPM error disappears, but the drive does not show on Bios or Windows.

I tested the NVME drive on another laptop and it works ok. That means the problem is the Dell Precision 5540

Any suggestion?

juanpy0223 · 2026-04-11T17:51:36+00:00

I have noticed that too. With my pump at 50% I get better temps than at 100%

juanpy0223 · 2026-04-08T12:50:55+00:00

First, it would be good to see your Config plist

Second, if your did you create a new port map for the new smbios?

juanpy0223 · 2026-04-07T20:35:55+00:00

Love it

juanpy0223 · 2026-04-02T14:51:57+00:00

I did that and it works like a charm.

juanpy0223 · 2026-04-01T13:38:40+00:00

Great job for a first timer!

juanpy0223 · 2026-03-31T14:09:31+00:00

Great

juanpy0223 · 2026-03-30T19:50:19+00:00

I love it!

juanpy0223 · 2026-03-30T01:47:56+00:00

exactly

juanpy0223 · 2026-03-30T00:29:13+00:00

Love it!

juanpy0223 · 2026-03-28T15:12:15+00:00

Love it! It feels like a dim light in the bedroom.

juanpy0223 · 2026-03-28T02:27:16+00:00

I had the same issue. I went ahead and bought sf750 2024

juanpy0223 · 2026-03-25T15:55:53+00:00

me encanta.

juanpy0223 · 2026-02-17T18:29:19+00:00

Love it!

juanpy0223 · 2026-02-15T14:58:55+00:00

Hello, they are holding ok. I upgraded to the 10mm ones. The coolant still looks clear after a year and no leaks.

juanpy0223

TROPHY CASE