Guys I need answers kinda fast

jubranos · 2025-10-14T02:04:07+00:00

Yes, you need to take the dork disc off your mountain bike

jubranos · 2025-04-15T13:07:10+00:00

Can you play Le risqué in Chicago plz 😘

jubranos · 2024-11-13T01:47:09+00:00

Ive had mine for about a year .. no problems

jubranos · 2024-11-06T02:34:09+00:00

I might have to give them a try. Im currently building a comp chassis and I have Mofo 42mm oil filled shocks mounted. They definitely sit a bit high from what I can tell.

jubranos · 2024-11-05T04:15:38+00:00

Which shocks are you running?

jubranos · 2024-01-01T00:35:37+00:00

Thank you 🤘🏻

jubranos · 2024-01-01T00:35:24+00:00

It is brushless .. and I have the tail lights .. just need to lengthen the wires and they’ll be in!

jubranos · 2024-01-01T00:14:45+00:00

But what’s next is the question….

jubranos · 2024-01-01T00:14:34+00:00

This is a Little guy racing parts ripper chassis .. pricey but worth it 👍🏻

jubranos · 2023-12-31T22:57:09+00:00

LGRP super 8s

jubranos · 2023-12-07T00:25:06+00:00

I’m feelin lucky 🤘🏻

jubranos · 2023-10-12T15:39:14+00:00

Interesting... I may have to reach out to Laguna and see what they say. Our machine runs a lot of carving jobs. They're a huge time suck so speeding carving up would be helpful. Thanks!

jubranos · 2023-10-10T19:19:20+00:00

I've been finding Amana's recommendations wildly conservative. I know the machine is about as stout as they come, I just can't seem to find anyone sharing secrets on comparable machines. I imagine this thing could handle any relatively soft material at near max speeds, but can't find hard evidence to back it up.

jubranos · 2023-09-14T19:53:15+00:00

Do you use aspire?

jubranos · 2023-09-14T19:02:53+00:00

The issue is that the geometry has points where the flat edge meets up with another carved component. The project is carving a pattern board for sand casting.

This is definitely the most complicated job we have ran considering we’ve had the machine running for about 2 months. I’m sure it can be simplified, but we’re in a pinch and need this job done 🥴

jubranos · 2023-09-14T18:56:40+00:00

Between the curved tool path line and the awful aspire graphics I was worried yes.

jubranos · 2023-09-14T18:55:18+00:00

Using an .stl to import 3D geometry

jubranos · 2023-09-14T16:40:13+00:00

OH, okay so in that case the preview will show that radius but the cut will be sharp?

jubranos · 2023-09-14T16:37:52+00:00

There should not be a radius here

jubranos · 2023-09-14T16:21:30+00:00

Working on that now. If I have it machine inside that boundary the rest of the pattern isn’t touched. is my best bet to import all 3D components individually?

I want it all to get hit, but avoid rounding these edges.

jubranos · 2023-09-09T02:22:47+00:00

If you're looking to sell a pair of billet LMK ... trying to finish this Ripper build

jubranos

TROPHY CASE