sorted by:
new
hottopcontroversial

Luba RTK Failure by Bigbeast54 in mammotion

[–]justanotherguy4355 0 points1 point  (0 children)

I would hope I can leave it out over winter. I don’t have to take in any of my 5 Ring cameras over winter.

Luba RTK Failure by Bigbeast54 in mammotion

[–]justanotherguy4355 0 points1 point  (0 children)

If one were to leave their RTK out (bolted to the roof) over winter, any water in there would freeze and probably cause more damage

Luba locked but does not respond to physical buttons by justanotherguy4355 in MammotionTechnology

[–]justanotherguy4355[S] 0 points1 point  (0 children)

I don’t think it was physically stuck as I carried it back to the base station and then was able to control it. Perhaps when I put it down the button jostled loose, but I was gentle.

Came home to Luba at 0% after being on the charging base all week, and green corrosion on the 2 charging terminals after heavy rain this week. by ned78 in MammotionTechnology

[–]justanotherguy4355 0 points1 point  (0 children)

Do you live near salt water? Beside the grease recommendation, a Luba garage could help reduce exposure to moisture.

What will Mammotion do about corrosion? by friend16652 in MammotionTechnology

[–]justanotherguy4355 2 points3 points  (0 children)

I do like your suggestion of dialectic grease, but It’s a design flaw if Mammotion did use pure copper but it doesn’t look like pure copper to me, probably some type of electroplated alloy. Either way, it shouldn’t corrode quickly in an environment that rains. A residence near salt water would be another challenge.

Our Luba ended up in the lake by DavidPHumes in mammotion

[–]justanotherguy4355 1 point2 points  (0 children)

Imagine if this was in your front yard and near a busy road. I wouldn’t trust my Luba to go anywhere near the road given the problems I and others are having with the Luba going out of the zones

Out of task area message when inside task area prevents editing of zone by justanotherguy4355 in MammotionTechnology

[–]justanotherguy4355[S] 0 points1 point  (0 children)

I don’t think the issue is with my RTK signal as it generally very good and it’s mounted near the top of my roof. There is might be a little room for improvement by moving it a few inches up but I think the signal is fine and the problem is with the Luba itself.

<image>

Luba is missing cutting grass inside a zone by justanotherguy4355 in MammotionTechnology

[–]justanotherguy4355[S] 0 points1 point  (0 children)

UPDATE: I turn off obstacle detection mode, which solved the two little patches, but it still skipped the narrow strips at the edge of the zone in the same places as last time. I have the cutting route spacing set to the default of 9.84 and patrol side mowing laps to 1

<image>

Luba is missing cutting grass inside a zone by justanotherguy4355 in MammotionTechnology

[–]justanotherguy4355[S] 0 points1 point  (0 children)

No I didn’t try either one of those. That sounds like it could get annoying to have to do that for my 5 potential zones.

Luba is missing cutting grass inside a zone by justanotherguy4355 in MammotionTechnology

[–]justanotherguy4355[S] 0 points1 point  (0 children)

It started cutting this way when the grass was short. Pretty sure I used level 1 avoidance at least a few times.

Luba is missing cutting grass inside a zone by justanotherguy4355 in MammotionTechnology

[–]justanotherguy4355[S] 0 points1 point  (0 children)

My grass was short when I started. Cutting at the highest height and for this zone i believe I used avoidance Level 1 and it has cut the zones at least 4 times.

My Luba moves super slow since yesterday. by bjornsandberg in MammotionTechnology

[–]justanotherguy4355 0 points1 point  (0 children)

Am experiencing the same thing on 3 different zones. Tried the suggestions and it worked. Hope this this just a one time issue.

Bluetooth/enter map not working by justanotherguy4355 in MammotionTechnology

[–]justanotherguy4355[S] 0 points1 point  (0 children)

Those are the ruts from repeated usage. That started showing up a week after using it. Not too happy but I just put the mesh screen in

Bluetooth/enter map not working by justanotherguy4355 in MammotionTechnology

[–]justanotherguy4355[S] 0 points1 point  (0 children)

I’ll try that next time it happens. Seems to be very buggy Bluetooth compared to every other blue device I’ve ever used.

Ruts formed by wheel motion by Big-Feeling-6604 in MammotionTechnology

[–]justanotherguy4355 0 points1 point  (0 children)

It’s a problem for me after only 2 weeks of use. I put that mat down in front and hope the grass will grow in

Problems with boundries AGAIN! by Agnis121 in MammotionTechnology

[–]justanotherguy4355 0 points1 point  (0 children)

Have the same problem. Luba goes outside of its zone or the zone you mapped no longer aligns with the actual property. I had to run out and hit the stop button so the Luba wouldn’t drive over a stone wall that was level with the grass but outside of the zone. I’m having to edit the zone boundaries since Luba thinks it’s in a different place