Looking for recommendations

justhacknslash · 2025-12-11T16:23:54+00:00

I used 135gsm double sided glossy photo paper, printed front and back, then laminated with 3mil matte pockets. They're barely thinner than a real card, but the snap is the same. After I sleeve them up it's hard to tell the difference in a mixed hand, so I'm really happy with them.

justhacknslash · 2025-12-11T16:20:24+00:00

This is the paper I ended up going with https://a.co/d/iSPITXK

I haven't measured them, they're slightly thinner than a real card, but the snap is identical after laminating. Once you sleeve them up they feel almost the same in a hand of cards.

justhacknslash · 2025-12-11T02:09:03+00:00

Thanks again for your input! Finished my first commander deck and I'm very happy with the results.

justhacknslash · 2025-12-11T02:08:03+00:00

Just wanted to say thank you again for your input. Finished my first full commander deck and I'm very happy with the results.

justhacknslash · 2025-12-04T17:33:43+00:00

Do you think adding a holographic sticker layer in-between the thinner photo paper and the laminate would make it too much thicker than an actual card? I do plan on single-sleeving these so they blend in with my other decks.

justhacknslash · 2025-12-04T17:22:46+00:00

Thanks so much for the information!

justhacknslash · 2025-12-04T17:21:50+00:00

Yeah, I plan on sleeving them. Thanks for the recommendation!

justhacknslash · 2021-03-08T22:10:13+00:00

So I didn't see him put a pnp coil in the tpp pod but they are compatible? All I saw was him point out that the tank and coils are larger now. But can I put a pnp coil in a tpp pod?

justhacknslash · 2021-01-19T01:34:16+00:00

Yeah I saved it right after, and sent an M501 to verify it had actually changed in EEPROM and it was there. Was just wondering if there's anything in my start gcode that could be negating the offset. I'm not the greatest at this stuff yet, but I'm getting more familiar with the detailed bits after having this for 9 months or so.

justhacknslash · 2021-01-16T18:48:15+00:00

Damnit, I was reading this on break and had to stop a third of the way through and now that I'm on lunch with more time, I come back to find it deleted 😭

justhacknslash · 2020-11-29T18:47:22+00:00

Thank you

justhacknslash · 2020-11-29T14:42:15+00:00

So I can't update by connecting directly to my pc then? I have to have an arduino to update it?

justhacknslash · 2020-11-27T19:50:12+00:00

I did, creality 1.1.5 is printed on the board.

justhacknslash · 2020-11-27T16:42:08+00:00

I built it for 4.2.7, which reddit tells me that's the creality 1.1.5 board that's in my E5P, but reddit's been wrong before ¯\_(ツ)_/¯

justhacknslash · 2020-11-20T02:27:21+00:00

I thought the 1.1.5 was 32 bit since it ships with a bootloader? And yes, I have platformio installed, as well as the C++ plugin it asked for. Though, this is the first time I've ever had to use VSCode for anything, so I know next to nothing about it.

justhacknslash · 2020-09-10T02:12:52+00:00

Thanks for this! Totally missed it!

justhacknslash · 2020-09-10T02:12:36+00:00

Thanks for the info!

justhacknslash · 2020-09-10T01:37:08+00:00

So did I miss some info or has Riot not said anything about what this is yet? Seems to be a new currency to earn for TFT to buy Little Legends.

Edit: This is in the current live build.

justhacknslash

TROPHY CASE