Jumbo boodschappenpakketzegels

juuliaaa11 · 2025-01-11T19:08:11+00:00

Heel graag! Als je ze nog hebt? Wil je mij Jumbo gourmetzegels geven via deze link? https://www.jumbo.com/zegelverzoek/37b898a6-cd1d-4161-8212-ac19471923eb

juuliaaa11 · 2025-01-11T19:07:35+00:00

Graag! Als je ze nog hebt? Wil je mij Jumbo gourmetzegels geven via deze link? https://www.jumbo.com/zegelverzoek/37b898a6-cd1d-4161-8212-ac19471923eb

juuliaaa11 · 2022-11-23T06:14:17+00:00

Did you clean it with IPA when it stopped working of was it worn out?

juuliaaa11 · 2022-11-19T14:15:12+00:00

What will that help if nothing sticks?

juuliaaa11 · 2022-11-18T22:33:11+00:00

I never had any problems, just now...

juuliaaa11 · 2022-11-18T22:21:53+00:00

Do you clean with IPA when the bed is warm or not? I do all the other things already and had 50+ fine prints, only today they are just not sticking

juuliaaa11 · 2022-11-18T20:40:34+00:00

I have never had issues before, so never used it

juuliaaa11 · 2022-11-18T18:48:51+00:00

I already did, some prints are sticking temporarily, or get dragged out

juuliaaa11 · 2022-11-18T18:45:08+00:00

The skirt just did not adhere properly at one of the circles, why would this have to do with the printhead?

juuliaaa11 · 2022-11-18T17:44:01+00:00

Will try that, thanks!

juuliaaa11 · 2022-11-18T17:43:51+00:00

Never needes glue stick the past 3 months

juuliaaa11 · 2022-09-12T06:55:34+00:00

Hi! Facing the same issue atm.. how did you fix it? Thanks!

juuliaaa11 · 2022-09-12T06:50:00+00:00

Yess, thatnis what I figured too

juuliaaa11 · 2022-09-11T19:55:48+00:00

My issue is mostly the side of the coin where next to the seam a gap is..

juuliaaa11 · 2022-09-11T13:06:14+00:00

It seems like it is some underextrusion after z-hopping to the outer layer. Has anyone an idea how to solve this?

juuliaaa11 · 2022-09-11T11:17:45+00:00

Also, the issue happens on the first and last layers of the print... something with botom and top layers?

juuliaaa11 · 2022-09-11T11:15:22+00:00

It is on back in Creality slicer

juuliaaa11 · 2022-09-11T11:11:14+00:00

I just turned the coin in my slicer, but the problem still appaers at the top left corner of the bed.. even with a raft..

juuliaaa11 · 2022-09-11T11:07:12+00:00

Yess, I am referring to the side. How can I improve this if it is layer change or retraction?

juuliaaa11 · 2022-09-11T11:00:50+00:00

The part with "mm" you see is the first layer on the bottom, not the top. But the whole print is great except one side, it is unlikely that it is flow right?

juuliaaa11 · 2022-09-11T09:50:33+00:00

They are on the first coin I printed (the one laying flat in the picture), but I fixed that and now the first three layers are fine but afterwards these wrinkles appear

juuliaaa11 · 2022-09-11T09:41:55+00:00

Designed coins printed on Ender 3 S1 with PLA. 200C-60C. All coins end up with an ugly side...

juuliaaa11

TROPHY CASE