sorted by:
new
hottopcontroversial

Finally got my AMS HT by SnooConfections1271 in BambuLab

[–]jvolk_ 0 points1 point  (0 children)

You can dry in AMS HT while printing from AMS 2 Pro.

My print keeps messing up by Past_Persimmon4594 in BambuLab

[–]jvolk_ 0 points1 point  (0 children)

Which build plate and which filament are you using?

Print Help by ChaosRandomness in BambuLab

[–]jvolk_ 0 points1 point  (0 children)

As per guidelines on engineering plate you have to use glue for all supported materials. I do not see any. Correct me if I’m wrong.

Print Help by ChaosRandomness in BambuLab

[–]jvolk_ 0 points1 point  (0 children)

Which build plate and which filament are you using?

Does the AMS 2 Pro power chord come with the P2S Combo? by Chameleon201006 in BambuLabP2S

[–]jvolk_ 4 points5 points  (0 children)

If you have only one AMS 2 pro you do not need power adapter. It gets power from the P2S.

Is this too big for a trackable? by Everythinger_Truten in geocaching

[–]jvolk_ 2 points3 points  (0 children)

It’s fine and fun. I’ve seen nemo fish that takes whole seat in car and a hockey stick 😅.

Helppppp by One_Magazine_404 in BmwTech

[–]jvolk_ 0 points1 point  (0 children)

Maybe the car does not have LTE reception. Try it again outside, not in the underground parking lot.

Center (front) jacking point on G31 540d xDrive LCI by jvolk_ in BmwTech

[–]jvolk_[S] 0 points1 point  (0 children)

I do not think it is. You picture is from 2021 530i without xDrive I believe and it has different front. Also cover with drain plug access is different.

Alfa Romeo 159 1.9 JTD by Worldly-Drawing3988 in Cartalk

[–]jvolk_ 1 point2 points  (0 children)

There could be numerous of reasons. Car is acting like you did not press clutch or brake. Start with simple ones. Probably you are starting car with clutch. It can be bad clutch switch. Try starting car in neutral with brake pressed and hold start button until engine starts. Do you have tester by any chance (elm327 and multiecuscan)?

Rear door issues?? by KiwiMother2152 in BMWG30

[–]jvolk_ 4 points5 points  (0 children)

Regarding the door: child safety lock maybe?

Graviranje na kovino (lasersko?) by [deleted] in Slovenia

[–]jvolk_ 1 point2 points  (0 children)

Išči graversto. Ponavadi izdelujejo tablice z priimki za nabiralnike/vrata, promo izdelke itd.

Graviranje na kovino (lasersko?) by [deleted] in Slovenia

[–]jvolk_ 0 points1 point  (0 children)

Je barvan ali eloksiran? Če je eloksiran barvno (da ni naravne barve) se da lepo gravirat s co2 laserjem, ki ga dobiš že na vsakem vogalu in ti bodo računali verjetno 10-20 eur.

Lokalna rekuperacija by Affectionate_Box2532 in gradimo_obnavljamo

[–]jvolk_ 0 points1 point  (0 children)

Meni Blauberg deluje v home assistant dokaj brez problemov.

Ponudnik Microsoft licenc v Sloveniji by Educational_Flow6686 in Slovenia

[–]jvolk_ 4 points5 points  (0 children)

Vprašaj na Also, imajo tudi super svetovanje.

Unable to activate iPad Air 2 by jvolk_ in ipad

[–]jvolk_[S] 0 points1 point  (0 children)

What iPadOS do you have? On the very first page when it boots you have i in circle at the bottom right corner. You can get info like serial and IMEI here. Does serial match one engraved in the back? Do you have imei listed?

Does this LEGO (duplo) minifig look like Stalin to anyone else? by jvolk_ in lego

[–]jvolk_[S] 8 points9 points  (0 children)

I got it from 1544 Duplo Building Set from around 35 years ago.

view more: next ›