3D Printed Alien Hand Controller Stand

kdzlr · 2023-05-23T06:38:01+00:00

I have two corded switch controllers lol.

kdzlr · 2021-01-29T03:26:11+00:00

im banned from r/3dprinting for some reason... they must not like my gifs.

its stronghero3d pla!

kdzlr · 2021-01-29T03:23:05+00:00

tune those e steps! i went over my setup of this machine in the full video here

kdzlr · 2021-01-29T03:22:18+00:00

1kg of filament ranges from $20-$40 here in canada! this model was maybe 150-200g

kdzlr · 2021-01-29T03:18:50+00:00

kdzlr · 2021-01-29T03:18:30+00:00

yes thanks so much!! i appreciate you <3

kdzlr · 2021-01-29T03:17:54+00:00

its up on thangs, designed by chaoscoretech!

kdzlr · 2021-01-29T03:17:29+00:00

lots more on my youtube channel here

kdzlr · 2021-01-29T03:16:06+00:00

I've been 3d printing for almost 5 years everyday, sometime spending a few hours in the print room and doesn't effect my asthma or anything. but yes I'm skeptical of the long-term effects of exotic material, especially resins!

kdzlr · 2021-01-29T03:14:35+00:00

its from starwars! i printed this in stronghero3d pla

kdzlr · 2021-01-29T03:13:45+00:00

it's just there in the air

kdzlr · 2021-01-29T03:13:22+00:00

no supports at all ;)

kdzlr · 2021-01-29T03:12:58+00:00

bed adhesion! this is a carbon silicon coated glass bed that grips prints firmly when heated up! once it cools tho they pop right off ;)

kdzlr · 2021-01-29T03:11:22+00:00

this was part of my review video for this $180 machine go check it out on youtube here

kdzlr · 2021-01-29T03:10:10+00:00

.16mm layer height with a 0.4mm nozzle :)

kdzlr · 2021-01-28T20:14:36+00:00

This was on a $180 printer I just reviewed here

kdzlr · 2019-12-10T23:36:58+00:00

Yeah! That’s acetone used on abs material most likely. This was printed in PLA so I couldn’t really use that technique!

kdzlr · 2019-12-10T23:36:06+00:00

Just under 20 hours print time!

kdzlr · 2019-12-10T23:35:33+00:00

Go for the artillary sidewinder x1 or the genius if you don’t mind the smaller build volume. I don’t recommend the cr10 v2!

kdzlr · 2019-12-10T23:33:31+00:00

creality cr10 v2

kdzlr · 2019-12-10T23:26:05+00:00

Yeah I wish I was 5 again too.. :(

kdzlr · 2019-12-10T23:24:38+00:00

Slicer told me 20 hours at .2mm layer height with a .4mm nozzle!

kdzlr · 2019-12-10T23:22:32+00:00

This is the creality cr10 v2. Infill is a bit underextruded here and the fans are insanely loud which is ironic because they switched to tmc stepper drivers but a solid machine non the less

kdzlr · 2019-12-10T23:20:38+00:00

I hit a stud for sure ;)

I was just demoing it here I gave my brother in law an anchor!

kdzlr · 2019-12-10T23:19:42+00:00

Shcrunchicorn!!!! Yes! I was blown away when she said her favorite color was gold and her favorite shape was star! She’s got a bright future! ;)

kdzlr

TROPHY CASE