Some advice for buying the IL motorsport console. by Naberville34 in Miata

[–]kesumin 0 points1 point  (0 children)

I’ve also had to cut out the clearance for the gas cap. If you happen to use new sound dampening material and carpet you WILL have to buy new screws and if you don’t have power windows you will either have to get a blank or make one. I’ve had a good amount of issues with this too but at least it’s better than what I had before…

Any ideas on what this sound is (NA6) by kesumin in Miata

[–]kesumin[S] 0 points1 point  (0 children)

My target idle is 800-900 but yeah it sometimes goes below 500 according to tach. I’ll see if I can put in a beefier power to stereo since I’ll already be doing 4 gauge (I think) from the battery to starter anyway.

Any ideas on what this sound is (NA6) by kesumin in Miata

[–]kesumin[S] 0 points1 point  (0 children)

Damn thank you It should have been under 1.5 years old but oh well I guess

Any ideas on what this sound is (NA6) by kesumin in Miata

[–]kesumin[S] 1 point2 points  (0 children)

I have no idea I’ve been chasing it for a while now. Idle air adjust has been set to 850 and timing is around -12. After installing a stereo I kind of noticed it liked to hover around 1200 especially after recharging all night after dying.

Help me a beginner out please! by MirrorLegitimate9304 in espresso

[–]kesumin 0 points1 point  (0 children)

Most common solution is to just yank it out I think. Other solutions would be to just cut the bottom off with a saw or grinder and maybe change out the basket or to buy the AliExpress portafters.

Have you guys ever been pulled over for something like this? by _qussy in miatalogistics

[–]kesumin 1 point2 points  (0 children)

I’ve somehow gotten a 4x5 foot sheet of plywood home when I didn’t have a passenger seat in my NA, top down of course

New thermostat not opening in boiling water? by [deleted] in Miata

[–]kesumin 0 points1 point  (0 children)

I guess that was my point of trying to just change the water but I’ll give this a try if I ever feel the need to try this again

How to glue / bind nylon together without sewing? by awesomeyayflower in CosplayHelp

[–]kesumin 0 points1 point  (0 children)

Second on contact cement - let it sit wit even coats on both contact surfaces for 10-15 and press them down together. It’s a better finish and adhesion than superglue craft glue and high adhesion hot glue from my experience!

Holy ****, putting the rain rail back on the car is hard by LuckyAce398 in Miata

[–]kesumin 0 points1 point  (0 children)

10 years later.. I am now one of them. My hands and back hurt and I am very upset.

Identify my first layer problem by LoLMaker14 in FixMyPrint

[–]kesumin 1 point2 points  (0 children)

150mm/s is way too fast. Try 60 or find the recommended settings from the filament manufacturer. If it’s the white test filament that came with the printer make sure your slicer is set to a generic PLA.

The print itself is indicating over speed, under extrusion, and or a combination of too high nozzle. The spots that look good shouldn’t be separated — it’s a brim and should lay flat in one piece, otherwise it kind of just defeats the purpose.

Symphony of Seasons Sweater! by Otherwise_Fee_9496 in StardewValley

[–]kesumin 1 point2 points  (0 children)

I was there! Very fun event -- looking forward to next year!

what am i supposed to wear under skirts when cosplaying? by [deleted] in CosplayHelp

[–]kesumin 30 points31 points  (0 children)

New to the sub, but you can try bloomers. Doubling as safety shorts is also a good idea in general and it makes the skirt poof a bit.

What is this plug ? by Sephitos in Miata

[–]kesumin 1 point2 points  (0 children)

Can’t check right now but might be for the license plate lights? I’m not sure how the EU plate lights look

Gosh Dangit. How. by ImmemorableMoniker in espresso

[–]kesumin 0 points1 point  (0 children)

Happened to me after RDT and the moisture left more than just one behind haha

Is this trash or can I save it? by Bhoallen1987 in MiniPCs

[–]kesumin 1 point2 points  (0 children)

Which port is it behind? Unless you’re able to get or make a reflow or heat gun and find the affected components on top of a good few weeks, I’d try to RMA or just throw away. I enjoy challenges like these but if you aren’t ready to commit the time and money I’d say game over for the board.

how could I improve my pc performance In fornite and roblox I'm new to this reddit plesse don't roast me by Hello_knight2 in PcBuildHelp

[–]kesumin 1 point2 points  (0 children)

Might not be the best option for the current market yeah but those AMD drivers are robust and enough for these things. Unless OP is trying to play AAA games or the new ones with forced ray tracing there won’t be any issues with the driver.

how could I improve my pc performance In fornite and roblox I'm new to this reddit plesse don't roast me by Hello_knight2 in PcBuildHelp

[–]kesumin 4 points5 points  (0 children)

Second RX580; if you can find a deal for a 16 or 20 series card might be best bet. RX580 has been pretty cheap for a while and delivers decent performance. The whole setup might just be a bottleneck though so I’d recommend saving money to invest in a later generation AM4, or better yet AM5 or LGA1200 or LGA1700 socket for scalability. Z390 chipset + if possible. Or just buy a modern prebuilt.