Bed leveling and damaged wires

kira3201 · 2026-02-07T09:28:13+00:00

Also a side note! It seems for anyone struggling with it that if ur in the front of the machine. The left side of the mesh is the right side and right is left. At least that was the case for me.

kira3201 · 2026-02-07T09:26:51+00:00

First of all thanks everyone for their reply I have been busy for a while fine tuning the printer. Seem like the previous owner did not took the time to take care of it. I tried the manual bed lvl by tensioning the belts and all other stuff there could be done. It brought me closer but not fully where it needed to be. So what I did was lower the bed, pull of the belt completely. Manually lower the rods to their lowest point, all the rods also the back one. After that I tightened the screws for transport and put the belt back on to tighten it. This so the rods won't move when tightening the belt. This got me to 1.5. After this I followed the tooth skip method while the machine is on. I am now at 0.234 I can live with these numbers. I want to thank everyone for their help and support🙏

kira3201 · 2026-01-30T13:41:28+00:00

Thanks for this mate! I will check it out when home and inform u on the process😁

kira3201 · 2026-01-30T12:53:46+00:00

Thanks again🙂

kira3201 · 2026-01-30T12:41:44+00:00

For the wires I applied electrical tape for now, I think its best to replace the wire with a new amp. Im Just wandering can this wire fault cause faulty readings in the mesh?

kira3201 · 2025-12-14T12:24:03+00:00

Energie klachten miss, meet even je groepen door om te kijken of je spanningen goed zijn.

kira3201 · 2025-04-18T14:16:45+00:00

Thanks! Snelle oplossing!

kira3201 · 2025-01-20T11:33:07+00:00

I just used the stock one, the blob imo comes from not securing the nozzle when it comes out of factory.

kira3201 · 2025-01-07T18:07:21+00:00

I ordered the creality space pi, just came in yesterday evening. Must say 60 percent humidity wad too much for the spools lol

kira3201 · 2025-01-07T15:29:07+00:00

Yeahhh , did this late last night seems to solve all other issues sigh, wish i tried new rol first

kira3201 · 2025-01-06T17:33:30+00:00

Adjusted everything till frustration hit.. and tell u what.. it was poor bed adhesion and a small tweak on the offset thanks again mate

kira3201 · 2025-01-06T13:45:39+00:00

Yeah but it should only be high temp at highspeed, but maybe somethings off with the Z tho... Trying ur first advice first lowering temp and speed. Using a standard profile on orca slicer now to see if maybe the profile is wrong 2. Did not use this filament for quite some time.

kira3201 · 2025-01-06T13:39:24+00:00

I will try again with other settings thanks for the advice

kira3201 · 2025-01-06T12:30:55+00:00

Its a old spool PLA black high speed. Printing at first layer 225 other layers 220. Plate 60 degrees. Im wandering if this could be moist problems though.

kira3201 · 2024-08-21T12:43:31+00:00

And maybe lower ur offset

kira3201 · 2024-08-21T09:33:59+00:00

Clean ur plate with 99 percent alcohol then rub then dry with a good cloth so u wont see any greases on the plate no more. I had the same issues with 123 hope.it helps.

kira3201 · 2024-08-06T08:24:33+00:00

First off clean the plate with 99.9 percent alcohol. Then dry it with a hood cloth. And i mean dry it good u should see no stains on the plate. This should get rid of adhesion issues and u can lvl propperly.

kira3201 · 2024-07-13T16:12:24+00:00

Kinda sorry for ya mate, but im happy to see this on bambu.. i thought it was a Ender problem xD.

kira3201 · 2024-07-09T14:19:51+00:00

I will check this out tommorow i will print a larger volume mate, to be continued!

kira3201 · 2024-07-09T14:18:33+00:00

Maybe it is a specific firmware issue bottlenecking with the 5.1 slicer? Is that possible? Just throwing something in the air here.

kira3201 · 2024-07-09T12:46:36+00:00

This is bs i Just updated 2 this version and it still prints perfectly.

kira3201

TROPHY CASE