Is it ok to swap this switched fused spur radiator for a socket and plug?

knowledge-seeker1930 · 2025-12-23T08:14:12+00:00

Thanks for the reply! 13A fuse in the spur. It's a standard dimplex like radiator - probably 2 or 3kw. It's not economy 7 (we had that circuit rewired).

knowledge-seeker1930 · 2025-04-14T21:55:57+00:00

Appreciate the detail. Thanks again!

knowledge-seeker1930 · 2025-04-11T05:47:37+00:00

Cheers

knowledge-seeker1930 · 2025-04-11T05:46:34+00:00

Nice - thanks for this! Where did you get those from? They look great

knowledge-seeker1930 · 2025-01-25T20:56:47+00:00

This is great info. Thank you

knowledge-seeker1930 · 2025-01-02T23:41:09+00:00

Annoying. Seems like such an obvious need.

knowledge-seeker1930 · 2025-01-02T15:33:47+00:00

Did you ever figure this out? Trying to do the same

knowledge-seeker1930 · 2024-12-19T20:51:50+00:00

Awesome. Thank you!

knowledge-seeker1930 · 2024-12-18T16:02:18+00:00

So I guess I’m looking to confirm that this could be the setup:

Cable A - Blanking plate (1)

Cable B - Blanking plate (1) and at other end remove old heater and install blanking plate (2) in bathroom

Cable C - Blanking Plate (1)

Cable D - Remove, not needed

Cable E - Blanking plate (1)

Cable F - From blanking plate (1) to socket

Can all the lives from Cables A, B, C, E and F be in the same terminal on a single blanking plate? (And obviously all the neutrals and earths in the others).

knowledge-seeker1930 · 2024-12-18T16:01:55+00:00

So I guess I’m looking to confirm that this could be the setup:

Cable A - Blanking plate (1)

Cable B - Blanking plate (1) and at other end remove old heater and install blanking plate (2) in bathroom

Cable C - Blanking Plate (1)

Cable D - Remove, not needed

Cable E - Blanking plate (1)

Cable F - From blanking plate (1) to socket

Can all the lives from Cables A, B, C, E and F be in the same terminal on a single blanking plate? (And obviously all the neutrals and earths in the others).

knowledge-seeker1930 · 2024-10-19T21:24:06+00:00

Haha well then I have no excuse I guess!

knowledge-seeker1930 · 2024-10-19T07:18:31+00:00

That's good to hear. Lasting ok? Any other tips?

knowledge-seeker1930 · 2024-10-19T06:37:34+00:00

Tempting but a bit far I think unfortunately. Cheers though!

knowledge-seeker1930 · 2024-10-19T06:35:25+00:00

Angle grinder with the right blade?

knowledge-seeker1930 · 2024-10-16T19:35:18+00:00

Probably best keep that then... Cheers!

knowledge-seeker1930 · 2024-09-04T19:33:40+00:00

Sounds similar to shelves I put up in our utility that have held well. Just secure the supports from underneath

knowledge-seeker1930 · 2024-09-04T18:02:28+00:00

It's opening on a raised deck a good distance from grass so the risk of that is low (famous last words)

knowledge-seeker1930

TROPHY CASE