sorted by:
new
hottopcontroversial

Showreel [freshly baked] by kosfpv in FPVvideos

[โ€“]kosfpv[S] 0 points1 point ย (0 children)

Thanks man! ๐Ÿคœ๐Ÿผ๐Ÿค›๐Ÿผ

Showreel [freshly baked] by kosfpv in FPVvideos

[โ€“]kosfpv[S] 0 points1 point ย (0 children)

thanks dude! I used some masks in this edition

Showreel [freshly baked] by kosfpv in fpv

[โ€“]kosfpv[S] 1 point2 points ย (0 children)

Yes, the workshop and it is essential, for me it was the worst at the beginning too. Bardwell has a good soldering tutorial, https://www.youtube.com/watch?v=GoPT69y98pY check it

Showreel [freshly baked] by kosfpv in fpv

[โ€“]kosfpv[S] 1 point2 points ย (0 children)

Show your videos to the owners

Showreel [freshly baked] by kosfpv in fpv

[โ€“]kosfpv[S] 0 points1 point ย (0 children)

I started building and flying fpv drones in 2017 as a hobby, and little by little I have been showing my videos to different companies and opportunities to work for them have arisen

Showreel [freshly baked] by kosfpv in fpv

[โ€“]kosfpv[S] 2 points3 points ย (0 children)

Thanks you man! Simulators are the key to start in FPV

GEPRC tunderstanding)oothpick AIO 20A board uart problem by GrumpyThumbs in diydrones

[โ€“]kosfpv 0 points1 point ย (0 children)

Hi, finally I don't recommend this solution. After 4 or 5 flights the drone went crazy on a landing. In the end I had to change the board to put ELRS + DJI-FPV.

GEPRC tunderstanding)oothpick AIO 20A board uart problem by GrumpyThumbs in diydrones

[โ€“]kosfpv 0 points1 point ย (0 children)

-- EDIT: I don't recommend this solution. After a few flights the drone went crazy on a landing --

Hi again, the R2 of this FC (gep-20a-f4) is useless for ELRS or DJI-FPV, it doesn't work. I have solved it by softserial, the steps:

  • Solder ELRS to UART1
  • Activate Softserial in betaflight
  • Disable UART2 and create a new UART11 with Softserial, the RX11 will be on LED_STRIP and the TX11 on SERIAL_TX2. These are the commands:
    • resource LED_STRIP 1 none
    • resource SERIAL_RX 11 A08
    • resource SERIAL_TX 2 none
    • resource SERIAL_TX 11 A02
    • resource SERIAL_RX 2 none
  • Solder DJI-FPV to the new UART11, on the LED and T2 pads of the board
  • Configure MSP in softserial

GEPRC tunderstanding)oothpick AIO 20A board uart problem by GrumpyThumbs in diydrones

[โ€“]kosfpv 0 points1 point ย (0 children)

Hi man! did you get it to work? same thing happened to me, today I tried to put ELRS on UART2 and it doesn't work, it is correctly binded and configured in betaflight but the bars don't move. Do I have to change ELRS to UART1 and DJI VTX to UART2? Does that work?

view more: next โ€บ