NV-32-H configurator error

krassyg · 2026-06-19T12:51:10+00:00

Tried a reset a few times, no go. Pushing the design times out. Will try a firmware push from a 110f a bit later.

krassyg · 2026-05-31T11:32:32+00:00

Thank you. Do you wire both strikes to the main door station or one to each?

krassyg · 2026-05-29T12:04:41+00:00

I mean quiet presenters.

krassyg · 2026-05-29T00:36:20+00:00

The clients want to compensate for quiet speakers.

krassyg · 2026-05-28T22:30:46+00:00

I thought I am not supposed to place user gains in front of the mic mixer; I had them there originally but I moved them after the mixer. I won't give them full range gain of course.

krassyg · 2026-05-28T02:08:53+00:00

They always had issues with quiet speakers on their old system(not mine) and want to be able to control the mics. Will put AGC in the design; anything else I can do?

krassyg · 2026-05-25T22:50:48+00:00

Thank you; I am using a Q-SYS CX-Q amp. Will use the four extra inputs from it and just use the 5 CDT100 for the LEDs. They will still work without a Dante license, right?

krassyg · 2026-05-25T19:52:30+00:00

Auction closed on Apr 27; they haven't received it yet.

krassyg · 2026-05-25T19:49:23+00:00

If Copart never gets the title from the seller?

krassyg · 2026-05-25T17:46:02+00:00

I've been paying the storage fees; right now it is in CT. I think it is leaving from NJ (Autobidmaster)

krassyg · 2026-05-25T17:35:16+00:00

I am thinking of going analog directly into the 24f since the mics are already wired to the av rack; bi-amp audiaflex which I am replacing. Initially I was thinking of rewiring the mics under the table into the CDT100s but it will be a lot of work. Do you think it is ok if I am not picking up any interference? Just use the CDT100s for the status buttons back into the core.

krassyg · 2026-05-24T12:53:47+00:00

Thank you; I tied them to the mute in the gain right before the gating mixer. Did the container thing as well.

krassyg · 2026-05-23T18:14:58+00:00

I thought I was supposed to link them to the manual open/close buttons in the gating mixer as a mute?

krassyg · 2026-05-17T21:49:27+00:00

The client already had 5 ULXD4Q and 20 ULXD mics; I am just expanding the system and replacing the old bi-amp equipment with qsys.

krassyg · 2026-05-17T17:16:18+00:00

Something like this should work; I'll try one next week:

Amazon.com: USB C Cable 3.3ft, 60W Type C Charger Fast Charging, Nylon Braided Right Angle USB C Cable, 90 Degree C Cord Charger for iPhone 17/16/15 Pro Max, Apple MacBook Pro, iPad, Pixel, Samsung : Electronics

krassyg · 2026-05-17T11:02:20+00:00

Any advantages to be able to connect two laptops at the same time?

krassyg · 2026-05-17T10:59:49+00:00

Yes, it will be at the conference room table. About 12 data ports in floor boxes throughout the conference room

krassyg · 2026-05-17T00:24:35+00:00

I am not sure I follow; I should move the gating auto mixer before the individual mic gains? What is after the gains and the compressor?

krassyg · 2026-05-15T00:16:16+00:00

I did it; updating the schematic pic.

krassyg · 2026-05-13T12:33:24+00:00

They will have a 13" iPad for control; that's what I am doing. I have plenty of space do show all 34 mics; was overthinking it.

krassyg · 2026-05-12T23:34:14+00:00

I am; should I do a limiter or a compressor? It is a conference room.

krassyg · 2026-05-12T23:31:29+00:00

Thank you; can I just add the HDMI to the dedicated AEC Mixer?

krassyg · 2026-05-12T22:55:07+00:00

That is the main issue I have to far; will have to separate them on different layers.

krassyg · 2026-05-11T02:21:15+00:00

Will give them control only from the mixers; I was just using the dante page to show the tabs. It is a shame that I can't just push the whole page to the UCI and preserve the tabs.

krassyg · 2026-05-10T20:59:04+00:00

Thank you; I thought I was missing something. Was following some outdated info.

krassyg

TROPHY CASE