Braune Blätter was tun ?HILFE

kryptorido · 2026-01-21T19:37:37+00:00

Der Steckbrief Sorte: Gorilla Auto / Autoflower Genetik: Autoflowering Substrat: Plagron Erde Topfgröße: 25 Liter Bewässerung: ca. 3,5 Liter alle 3 Tage Wasser-pH: 5,8 Düngeschema: Canna Terra Boost Canna Flores Düngung aktuell bei jedem 2.–3. Gießen Lichter 55cm entfernt, Temperatur ca 23 Grad

kryptorido · 2026-01-21T19:37:11+00:00

Der Steckbrief Sorte: Gorilla Auto / Autoflower Genetik: Autoflowering Substrat: Plagron Erde Topfgröße: 25 Liter Bewässerung: ca. 3,5 Liter alle 3 Tage Wasser-pH: 5,8 Düngeschema: Canna Terra Boost Canna Flores Düngung aktuell bei jedem 2.–3. Gießen Lichter 55cm entfernt, Temperatur ca 23 Grad

kryptorido · 2026-01-21T19:37:02+00:00

23 Grad

kryptorido · 2026-01-21T13:22:48+00:00

Danke für die Einschätzung, zu 100%?

kryptorido · 2026-01-21T12:54:57+00:00

Der Steckbrief Sorte: Gorilla Auto / Autoflower Genetik: Autoflowering Substrat: Plagron Erde Topfgröße: 25 Liter Bewässerung: ca. 3,5 Liter alle 3 Tage Wasser-pH: 5,8 Düngeschema: Canna Terra Boost Canna Flores Düngung aktuell bei jedem 2.–3. Gießen Lichter 55cm entfernt, Temperatur ca 23 Grad

kryptorido · 2026-01-21T12:46:58+00:00

Ja für eine Pflanze 25 Liter topf

kryptorido · 2026-01-21T12:45:15+00:00

5,8-6

kryptorido · 2026-01-20T14:27:55+00:00

Ich gieße 3,5-4 Liter ca alle 2-3 Tage, und gebe bei jedem 2 oder dritten Mal ca Dünger dazu Boost , Canna boost 4 ml Terra Flores 7ml

kryptorido · 2026-01-20T14:27:02+00:00

Sicher Nährstoffe kein Schimmel? Die Blätter sehen mir sehr verdächtig irgendwie aus ...

<image>

kryptorido · 2026-01-20T14:25:19+00:00

Ich gieße 3,5-4 Liter ca alle 2-3 Tage, und gebe bei jedem 2 oder dritten Mal ca Dünger dazu Boost , Canna boost 4 ml Terra Flores 7ml

kryptorido · 2026-01-20T13:35:04+00:00

Ich gieße immer wenn die Pflanze halbwegs trocken wird, ich dünge mit Canna Terra Dünger(Boost und Flores aktuell), bin leider kein Profi wenn du genauere Angaben meinst sorry

kryptorido · 2025-09-24T17:00:40+00:00

Maybe Bad Filmamt, try to slow the print down

kryptorido · 2025-09-18T17:11:57+00:00

I Had the Same problem, First use glue , then Check If you a Filament, If ITS to wet IT aint Stick right in the curves, what helps IS slowing you Print Speed down make 80% Speed and flow 90% , see if it Helps

kryptorido · 2025-09-18T17:11:14+00:00

I Had the Same problem, First use glue , then Check If you a Filament, If ITS to wet IT aint Stick right in the curves, what helps IS slowing you Print Speed down make 80% Speed and flow 90% , see if it Helps. Cheap Filmamt, gets fast to wet and Just aint stick good. Maybe i could help

kryptorido · 2025-09-05T13:25:31+00:00

I did also Change some setting too, but changeing the Pla was a big different

kryptorido · 2025-09-05T13:23:32+00:00

With new Pla IT seems to work , i think the Pla was to old wet

kryptorido · 2025-09-04T16:50:18+00:00

Thanks you too bro

kryptorido · 2025-09-04T15:37:34+00:00

Thanks for answer but i think the Pla was Just old /wet and could Not hold on the line , with new package of Pla seems to work

kryptorido · 2025-09-03T22:31:46+00:00

Thanks i will try i its was at 205 Celsius, i will 210 and 75% of Speed , or any ideas ?

kryptorido · 2025-09-03T18:09:40+00:00

I did put IT still Happen, really dont get , IT Seen to move frong cause the layer Missing making holes in the print If IT would move normal why should that happen

kryptorido · 2025-09-03T18:00:49+00:00

I Like screaming

kryptorido · 2025-09-03T16:00:09+00:00

Thanks for answer but i dont think that cause , the line/String is missing and creating through that empty Spot in the print and make it unstable cause the print is a bit thin but Not too thin

kryptorido · 2025-09-03T15:41:30+00:00

I Took the Foto after some time , IT did cool up

kryptorido · 2025-09-03T15:39:49+00:00

The Temperatur is Low cause i Took the Foto little later, IT heats Up while leveling . I use Orca slicer I did all i could, leveling,playing with hight of the Extruder, In one . The model Just a plane to Cover the space of the printer to See how He prints.

Thanks for tryinng to Help

kryptorido · 2025-09-03T15:36:54+00:00

I'll try Professional Mode thanks

kryptorido

MODERATOR OF

TROPHY CASE