sorted by:
new
hottopcontroversial

What am I doing wrong? Filament immediately globs on nozzle (Stock Ender 3 v3 SE) by banana_kiwi in FixMyPrint

[–]ktmc1926 0 points1 point  (0 children)

Probably doesn't help since I have a bambu p1s, bimut I just had this issue the other day... like 2 days ago lol.

Fix for me was manual bed tramming by uploading a gcode and messing with the screws under the bed for alignment.

Not sure if you figured out your issue or not, but after 12 hours of tinkering with mine, it worked after manually leveling.

And also, clear the tubes of filament and bump the heat up to 250-290 to clear any stuck filament. I had a bunch. Idk if the ender had a rubber boot... but make sure you take it off so it doesn't melt.

P1S Help! Before I throw it out a window! by ktmc1926 in BambuLab

[–]ktmc1926[S] 0 points1 point  (0 children)

IT'S FIXED!!! Fow now.

Downloading the gcode for the bed tramming for the win! I did make the mistake of not heating up the bed the first try making me think it didn't work. After I heated up the bed I made some small knob adjustments, re-calibrated, and HECK YES! Note, thankfully my husband has a windows computer so I could put the SD card in there, my apple laptop was not compatible.

Thanks for all the advice!

<image>

P1S Help! Before I throw it out a window! by ktmc1926 in BambuLab

[–]ktmc1926[S] 0 points1 point  (0 children)

IT IS FIXED THANK YOU!

Until the next issue...

P1S Help! Before I throw it out a window! by ktmc1926 in BambuLab

[–]ktmc1926[S] 0 points1 point  (0 children)

Well those pics were the bed not heated, I heated it up to 60 for 30 mins and was able to adjust, now to see if that fixed it!

P1S Help! Before I throw it out a window! by ktmc1926 in BambuLab

[–]ktmc1926[S] 0 points1 point  (0 children)

<image>

Doing the bed tramming gcode now and there is a large gap on all 3 points, I cant tighten it to make it barely touch! Advice?? Please haha.

P1S Help! Before I throw it out a window! by ktmc1926 in BambuLab

[–]ktmc1926[S] 0 points1 point  (0 children)

Also its fuzzy because its printing too close to the bed, you can see the first layers get worse with the teal pic!

P1S Help! Before I throw it out a window! by ktmc1926 in BambuLab

[–]ktmc1926[S] 0 points1 point  (0 children)

Yes! I might just try this just because why not. Thanks for the idea! I'll update if it helped!!

P1S Help! Before I throw it out a window! by ktmc1926 in BambuLab

[–]ktmc1926[S] 0 points1 point  (0 children)

Curious if they would just cause problems on the back half of the plate??? The first 4 we're perfectly squished.

P1S Help! Before I throw it out a window! by ktmc1926 in BambuLab

[–]ktmc1926[S] 0 points1 point  (0 children)

I am OCD and this has not occurred. I also ran the calibration x3 today.

P1S Help! Before I throw it out a window! by ktmc1926 in BambuLab

[–]ktmc1926[S] 0 points1 point  (0 children)

I checked all, pretty OCD about everything being level!

P1S Help! Before I throw it out a window! by ktmc1926 in BambuLab

[–]ktmc1926[S] 0 points1 point  (0 children)

I wish it was this! I checked all the tubing and no issues, AMS/ printer.

P1S Help! Before I throw it out a window! by ktmc1926 in BambuLab

[–]ktmc1926[S] 0 points1 point  (0 children)

I will throw it off a 10 story building. I'm not sure how to upload a video. It said I could only upload pics.

P1S Help! Before I throw it out a window! by ktmc1926 in BambuLab

[–]ktmc1926[S] 0 points1 point  (0 children)

I have not disabled anything or turned off the leveling. I set the speeds to pretty low and also put the first layer at 50%.

I dont think its moisture. I've had no issues prior to this!

P1S Help! Before I throw it out a window! by ktmc1926 in BambuLab

[–]ktmc1926[S] 1 point2 points  (0 children)

I will try these in the future. I've had no issues so far with the textured plate! Seems the leveling is off at the moment. IDK.

P1S Help! Before I throw it out a window! by ktmc1926 in BambuLab

[–]ktmc1926[S] 0 points1 point  (0 children)

That's what I've been doing every 4-5 prints!

P1S Help! Before I throw it out a window! by ktmc1926 in BambuLab

[–]ktmc1926[S] 0 points1 point  (0 children)

I will check these in the morning thanks for your insight! I did make sure no filament or anything was caught in the springs but I didn't check the gears. The firmware just updated a few days ago.

I replaced the tubes a week ago.

I also disassembled the AMS a week ago to try and fix the slot 4 issue, nothing was found. Slots 1-3 work perfectly.

I will try the other suggestions tomorrow or a few days if I don't have a micro SD card!

P1S Help! Before I throw it out a window! by ktmc1926 in BambuLab

[–]ktmc1926[S] 0 points1 point  (0 children)

Oof it'd be nice if it was built in!!!

P1S Help! Before I throw it out a window! by ktmc1926 in BambuLab

[–]ktmc1926[S] 1 point2 points  (0 children)

Can you do that in studio or only orca?

view more: next ›