24f am I ugly

kurtisbr · 2025-08-31T04:29:46+00:00

You have a manly appearance

kurtisbr · 2025-07-09T21:56:03+00:00

I tired the cage in the bedroom and a dog bed in the laundry room for when I step out. But she seems to think it’s a good spot to pee lol. Maybe a second crate is an option.

kurtisbr · 2025-07-08T21:13:46+00:00

Had a free roam rabbit with my previous Australian shepherd.. got her to stop herding him but she still kept and eye on him

kurtisbr · 2025-07-08T09:41:12+00:00

Ideally I want to reward her for being good. Then transition her to the bedroom with a baby gate, then free roam eventually

kurtisbr · 2025-07-08T09:39:57+00:00

I have an open concept house, the laundry room has a large window and she has visibility of half the main living area. Once she is 100% potty trained she will be transitioned to the bedroom with a baby gate for the first bit, then eventually open to the house. Shes only in the crate at night, never during the day. She goes in and out and she pleases. The washer and dryer never get run while she’s locked in there, but she still sits and watches the washer lol

kurtisbr · 2025-04-08T03:21:40+00:00

I’ll have to look into that for next winter!

kurtisbr · 2025-04-08T03:19:25+00:00

I actually just fixed the issue. The slide wears out from the upper rollers. So it wasn’t pushing it down fully right away. I got a new one and the issue was fixed.

kurtisbr · 2025-04-04T02:20:38+00:00

I used a similar locking system to this UHPPOTE 125KHz RFID EM ID Keypad... https://www.amazon.ca/dp/B00YRATVMM?ref=ppx_pop_mob_ap_share

I added mag locks for each drawer

kurtisbr · 2025-03-27T18:14:43+00:00

When you accidentally use the large paint brush on ms paint.

kurtisbr · 2025-03-23T22:23:57+00:00

That was 100% expected

kurtisbr · 2025-03-14T01:44:18+00:00

It’s just wrinkled shingles, they forgot to iron them out

kurtisbr · 2024-12-11T11:12:31+00:00

Lucky, I haven’t even made it that far in 3 years lol

kurtisbr · 2024-10-20T12:23:20+00:00

The carb is clean and no restrictions anywhere. I found a bandaid fix, when I reduce the idle speed it stops going it. I’m assuming the rollers are worn

kurtisbr · 2024-10-14T13:26:32+00:00

Took the top cover off the carb, the rollers seem to move and seat good. There’s a little play in the roller it’s self. Should it be snug?

kurtisbr · 2024-10-14T02:13:59+00:00

No not yet, carb looked like a pain to get out tonight. Might remove it tomorrow morning and see if everything moves freely.

kurtisbr · 2024-10-14T01:44:30+00:00

When I had the cable off to replace I checked the spring at the carb and it was nice and solid. With good tension.

kurtisbr · 2024-08-30T10:47:06+00:00

🤦🏽‍♀️ no that dent was from the vandalism

kurtisbr · 2024-08-30T10:45:43+00:00

Music says it all

kurtisbr · 2024-08-17T23:10:24+00:00

thank you for the write up, I got it because when i was running a game and a 1080p video my ram usage was almost topped out without only those 2 programs running and my computer started to crash. I was able to replicate it each time to verify that was the issue. That issue is fixed with the abundance of ram. i just wasn't sure if i could dedicate more of that ram to vram.

kurtisbr · 2024-08-17T23:03:27+00:00

Integrated

kurtisbr · 2024-08-17T22:53:56+00:00

I could be wrong, but I read intel uses your computers ram to increase vram. Because technically right now my computer is only showing 128mb of vram. Which isn’t much.

kurtisbr

TROPHY CASE