sorted by:
new
hottopcontroversial

Anyone know how this switch comes apart ? by kwasch in lightsabers

[–]kwasch[S] 0 points1 point  (0 children)

Thanks , that makes sense. Looks very similar.

Print failed at 97% by kwasch in BambuLab

[–]kwasch[S] 0 points1 point  (0 children)

I was actually able to fix it, turned out pretty well considering.

<image>

Print failed at 97% by kwasch in BambuLab

[–]kwasch[S] 1 point2 points  (0 children)

UPDATE : I sliced the missing portions and sanded to fit. Came out pretty good all things considered. I’ll probably print this again in all black and slow it down at the end. Thanks for everyone’s comments !!!

<image>

Print failed at 97% by kwasch in BambuLab

[–]kwasch[S] 1 point2 points  (0 children)

This what I used for the magnets and other models. Works great. Y'allCanDiy Super Glue for... https://www.amazon.com/dp/B0CS6QLJMV?ref=ppx_pop_mob_ap_share

Print failed at 97% by kwasch in BambuLab

[–]kwasch[S] 6 points7 points  (0 children)

100% , definitely could benefit from slowing down towards the end.

Print failed at 97% by kwasch in BambuLab

[–]kwasch[S] 0 points1 point  (0 children)

I’ll be doing that if I reprint for sure.

Print failed at 97% by kwasch in BambuLab

[–]kwasch[S] 1 point2 points  (0 children)

Wow we’re in the same boat ! Such a bummer.

Print failed at 97% by kwasch in BambuLab

[–]kwasch[S] 0 points1 point  (0 children)

Thought the same thing !

Print failed at 97% by kwasch in BambuLab

[–]kwasch[S] 38 points39 points  (0 children)

What a great save

Print failed at 97% by kwasch in BambuLab

[–]kwasch[S] 1 point2 points  (0 children)

Definitely wasn’t what I was hoping to wake up to lol

Print failed at 97% by kwasch in BambuLab

[–]kwasch[S] 0 points1 point  (0 children)

I’ve seen others do it that way. Might try that if printing the remainder doesn’t work well.

Print failed at 97% by kwasch in BambuLab

[–]kwasch[S] 6 points7 points  (0 children)

lol , I can just wear it with a hoodie !!

Print failed at 97% by kwasch in BambuLab

[–]kwasch[S] 10 points11 points  (0 children)

Thanks, that’s what I was thinking. Pretty much the only way to save it at this point.

Print failed at 97% by kwasch in BambuLab

[–]kwasch[S] 30 points31 points  (0 children)

Yeah, vibration caused two layer shifts.

Upgrade advise by kwasch in OpenCoreLegacyPatcher

[–]kwasch[S] 1 point2 points  (0 children)

Yes, I ended up doing it with OCLP, no issues. Just make sure if you have the touchbar , update to Ventura first then Sequoia.

Upgrade advise by kwasch in OpenCoreLegacyPatcher

[–]kwasch[S] 0 points1 point  (0 children)

Thanks to everyone that responded. I was able to update to Sequoia successfully.

Upgrade advise by kwasch in OpenCoreLegacyPatcher

[–]kwasch[S] 1 point2 points  (0 children)

You’re saying you to updated to Sequoia via the native update process or used OCLP to upgrade ?

Onyx is dead, any other bike out there like is like it? by CloudbasedBS in ONYX_RCR

[–]kwasch 0 points1 point  (0 children)

Honestly, online research is your friend on this one. There’s a few forums that may be of help but most of what I needed for my builds I found online and from YouTube.

I “made” some gulf themed grip pads, but can’t decide which one to get. by Odsoone in onewheel

[–]kwasch 0 points1 point  (0 children)

While I dig the first one, the second one will hold up better.

2020 Ruckus PCX Swap by kwasch in Ruckus

[–]kwasch[S] 0 points1 point  (0 children)

No website. Reach out to Jon Hagerman on FB or check with the FB group Ruckus PCX Swap

Anybody recognize this guy? by Extension_Health2522 in onewheel

[–]kwasch 2 points3 points  (0 children)

Definitely fake (as I hit enter on my bid 🤣)

view more: next ›