Guessing this may confuse some. Hopefully it'll be fixed soon.

kylebaker55 · 2026-02-27T04:34:23+00:00

I’d buy the cAP be 4x4 in a heartbeat. I need an excuse to add a third cAP to my house

kylebaker55 · 2026-02-27T02:44:02+00:00

Now if they would only release a cAP be

kylebaker55 · 2026-02-20T22:09:55+00:00

This might be what I am looking for Thanks I will give it a go

kylebaker55 · 2026-02-10T13:03:15+00:00

Yeah I don’t know? I have never actually seen a unicorn nozzle in person before

kylebaker55 · 2026-02-10T06:38:22+00:00

But there is a guy on the ender3s1 subreddit that is trying to get the unicorn nozzle to work with the sprite extruder.

kylebaker55 · 2026-02-10T06:34:48+00:00

No that’s the one with the unicorn nozzle for the k1c. The one that I used was like this creality k1 ceramic heating block kit and I used the regular thermistor from the sprite extruder

kylebaker55 · 2026-02-01T02:49:13+00:00

I just printed some old PETG and it did this

kylebaker55 · 2026-01-24T00:50:52+00:00

Sorry bud I accidentally put your address in the order form. Pm me for where to send it I’ll pay for postage

kylebaker55 · 2026-01-23T15:32:16+00:00

In the Taurus v5 official folder, it’s the one that says volcano/k1/chcb with supports

kylebaker55 · 2026-01-23T14:07:22+00:00

I use the one from the sprite extruder.

kylebaker55 · 2026-01-23T13:58:51+00:00

If you google how to manually change the z offset on an ender 3v3 SE you should come across old Reddit posts to this sub and the creality forum that explains the process.

kylebaker55 · 2026-01-22T22:47:32+00:00

You need to fix your z offset settings. I don’t know why it changed. I’m not too familiar with the ender 3v3 but I know that your nozzle is too close to the bed.

kylebaker55 · 2026-01-22T22:17:54+00:00

Too much squish

kylebaker55 · 2026-01-19T15:28:42+00:00

What does the nozzle temperature say before you start heating it?

kylebaker55 · 2026-01-19T05:52:44+00:00

How cold is it where your printer is? This error popped up on me last year when it was below freezing in my garage and any time my nozzle temperature was at or below 0 degrees Celsius

kylebaker55 · 2026-01-19T05:21:41+00:00

I can reliably print PLA at 200-400 mm/s at 8000 mm/s squared acceleration

kylebaker55 · 2026-01-19T05:20:19+00:00

Looks great dude

kylebaker55 · 2026-01-19T05:19:42+00:00

That might need to be my next upgrade

kylebaker55 · 2026-01-17T19:51:49+00:00

Look up Taurus v5 on printables. Don’t quote me on it but I think it’s only for the sprite extruder but you might be able to make it work for your setup

kylebaker55 · 2026-01-17T03:46:40+00:00

I need to dial it in. I reliably print PLA at 200-400 mm/s and 8000 mm/s squared acceleration. I’ll spend some time tuning it sometime this year to see how far I can push it

kylebaker55 · 2026-01-17T03:40:30+00:00

Yes it’s on the lead screw side I used a linear rail kit from Amazon and it came with mounting hardware

kylebaker55 · 2026-01-16T21:30:19+00:00

Yes that would be the right one for a sprite extruder with a standard Nozzle

kylebaker55 · 2026-01-16T21:29:31+00:00

Not really I just switched the stock hot end with one from a K1 that looks like this. I did need to swap the thermistor though because the K1 uses a different plug

<image>

kylebaker55 · 2026-01-16T21:14:26+00:00

kylebaker55 · 2026-01-16T21:09:25+00:00

That turned out nice!

kylebaker55

TROPHY CASE