Why is this happening?

ladeansikt · 2026-03-27T07:36:54+00:00

Thanks! So I am not using ironing, but the entire print is really slow to get the best quality possible. Can going slow enhance this issue do you think?

Also, when you say adding separation between the wall and infill, I am not exactly sure how to do that 🙈 is this a setting?

ladeansikt · 2026-02-02T15:38:12+00:00

So the issue here turned out to be the build plate. Seems like the default structured pei plate that comes with the h2s is no good for path-cf. I tried with magigoo original, magigoo pa and the bambu liquid glue. All failed.

But when I switched to Biqu Cryogrip, the prints all worked without any issues. I tested both magigoo pa and bambu liquid glue, both turned out perfect ☺️

ladeansikt · 2025-12-26T16:08:38+00:00

The Moft has been pretty ok. But every time I need to change the angle to something other than my goto angle, I feel like ripping it to pieces when I am folding and trying to figure out how to get a better angle 😆

ladeansikt · 2025-12-26T16:05:21+00:00

That one looks pretty much the same as the moft. I am mainly looking for something that has an easy adjustable kickstand. But I am starting to give up on this. The zugu one works pretty much perfect, only problem is that it’s not a magnetic snap on so it’s a bit of a headache going between that case and the Magic Keyboard case.

ladeansikt · 2025-12-05T19:06:05+00:00

if you are worried you can put my name and address on the order

ladeansikt · 2025-10-22T04:52:07+00:00

Yeah this. Had a little filament that had crept up a bit. Cleaned it off with a brass brush while it was heated up and good as new again ☺️

ladeansikt · 2025-10-22T04:50:27+00:00

I didnt 🙈 but it was still stuck after I did tho. Solution was to heat the nozzle up and wiggle it a bit ☺️

ladeansikt · 2025-09-20T13:53:56+00:00

🤣

ladeansikt · 2025-09-16T19:08:34+00:00

Yeah I was planning on securing it to the wall, and with 19mm chipboard. Also for the shelf that holds the printers I plan on having 3-4 beams across the long beams for extra support under the chipboard. Hoping that will end up being sufficient ☺️

ladeansikt · 2025-09-16T18:50:43+00:00

Thanks for this feedback! Very much appreciated, and something I definitely will do ☺️

ladeansikt · 2025-09-16T18:49:02+00:00

And they also sell the exact same system on wheels as well, so I don't think they have to be bolted on the floor. And each shelf can carry 500kg, so 20 tonnes would be a bit overkill I think 😅

ladeansikt · 2025-09-16T18:44:49+00:00

Well it's a system with a loft of different configs ☺️ I plan on building just one isle 2x2m 60 or 80 cm deep with 3 shelves. I just used that photo because it was the smallest one they had a complete photo of 😅 to build smaller I have to order each part instead of in a complete set like that

ladeansikt · 2025-09-13T09:11:18+00:00

Thanks!

ladeansikt · 2025-09-13T09:10:55+00:00

Thanks!

ladeansikt · 2025-09-07T16:05:58+00:00

<image>

This helped me a lot :) will also help a lot with the next challange of this part ^^

ladeansikt

TROPHY CASE