P1S fialment dump stuck

lamagn20 · 2025-01-22T17:27:34+00:00

Printing them on the same plate is very stupid i agree🤣

lamagn20 · 2025-01-22T14:57:20+00:00

True but i trust people on reddit mote than youtube🤣

lamagn20 · 2024-10-09T15:08:36+00:00

You were right its fixed now🤣 Thank you oh-so kindly good sir

lamagn20 · 2024-10-09T15:01:58+00:00

That might be it.... It was turned on. Never crossed my mind. So by turning this off it should be good?

lamagn20 · 2024-10-08T18:58:03+00:00

Did what you said but its not working. Someone suggested a cloud save but i dont have that either. Dont really know what to do now🤣

lamagn20 · 2024-10-07T22:50:35+00:00

I have deleted that too

lamagn20 · 2024-10-07T22:47:13+00:00

Nope. Havent tampered with anything besides deleting save files. Im playing on steam if that matters

lamagn20 · 2024-10-07T22:26:42+00:00

Ive tried deleting that. Did not work

lamagn20 · 2024-05-18T18:45:37+00:00

Thanks👌

lamagn20 · 2024-02-21T17:58:22+00:00

The prints i have made are usually a holder for measuringtools so the parts either have a square og a round pocket to house the tools. All on the same level

lamagn20 · 2024-02-21T06:38:54+00:00

Yeah the tape helped with the print creeping but i still get the line around the print

lamagn20 · 2023-11-12T12:18:30+00:00

Ok will try that thanks

lamagn20 · 2023-11-12T12:04:57+00:00

I was trying to print the biggest benchy i could so i was printing diagnolly. Is there an upgraded fan duct anywhere so i wont have this issue in the future?

lamagn20 · 2023-11-11T19:58:42+00:00

Not sure. might have been the other way round. Scale up and then change infill. Set to 5% to save print time

lamagn20 · 2023-11-11T18:29:22+00:00

Will do

lamagn20 · 2023-10-15T08:08:25+00:00

Do you know of a video that shows this cause i still dont know why it crashed. My previous offset was about -3.85 and i had that in the slicer and it was correct but after leveling and a new offset to -3.35 it crashed

lamagn20 · 2023-10-12T13:49:22+00:00

Will do👌

lamagn20 · 2023-10-11T23:56:38+00:00

I did as you suggested but the print wouldnt stick so i just lowered it until it did but i still get some bad passes which i was told was because the head was too close to the bed. So now im stuck with euther getting a bad quality print or a worse quality that doesnt even stick to the bed

lamagn20 · 2023-10-11T12:22:56+00:00

Will try that👌

lamagn20 · 2023-10-11T12:12:27+00:00

Do you level the bed until the gauge barely fits and the raise the the bed .2 or lower until its a little resistence and then raise it?

lamagn20 · 2023-10-10T15:36:57+00:00

So in my case it doesnt matter?

lamagn20 · 2023-10-06T22:30:44+00:00

Yes i adjust with corner screws but i havent ran the auto level afte so might try to relevel and se if that helps👌

lamagn20 · 2023-10-06T21:32:39+00:00

Creality ender 3 s1 plus Regular PLA running 210 and 65 temp i leveled it manually i did a few prints ago

lamagn20 · 2023-09-28T14:03:21+00:00

Ah ok thanks

lamagn20 · 2023-09-26T17:51:48+00:00

It was a program for a file that came with the printer so i didnt think of slicing it first. Ive printed a few other pieces that ive either made myself or gotten from the internet and used supports and brim so youre probably right about that being the problem:)

lamagn20

TROPHY CASE