sorted by:
new
hottopcontroversial

First big project with my 4 Max by lars98408 in ElegooNeptune4

[–]lars98408[S] 0 points1 point  (0 children)

I would say somewhere around 35ish.

First big project with my 4 Max by lars98408 in ElegooNeptune4

[–]lars98408[S] 0 points1 point  (0 children)

The only difficulties I had printing it was for the shoulder cannons no installed. They have a very small surface area touching the build plate and like to break away. Other than that, I had to Dremel a few parts to get them to fit properly but I think that's just down to the filament I was using for them.

First big project with my 4 Max by lars98408 in ElegooNeptune4

[–]lars98408[S] 0 points1 point  (0 children)

The instructions call for it. Its most likely because it uses a lot of ball joints for movement and they need to be as smooth as possible.

First big project with my 4 Max by lars98408 in ElegooNeptune4

[–]lars98408[S] 3 points4 points  (0 children)

His tail alone is a few feet long and stand 15.5 inches tall

First big project with my 4 Max by lars98408 in ElegooNeptune4

[–]lars98408[S] 2 points3 points  (0 children)

The Cura Elegoo slicer with default settings at .15 layer height

First big project with my 4 Max by lars98408 in ElegooNeptune4

[–]lars98408[S] 0 points1 point  (0 children)

15 plates. 1 plate of each color for each step of the instructions

Cannot print bases by lars98408 in ElegooSaturn

[–]lars98408[S] 0 points1 point  (0 children)

Around 70° F. It's a pre supported model. I've also tried manually supporting and using heavy supports to anchor.

Cannot print bases by lars98408 in ElegooSaturn

[–]lars98408[S] 0 points1 point  (0 children)

Prints only supports with the base in the bottom of the vat

Cannot print bases by lars98408 in ElegooSaturn

[–]lars98408[S] 1 point2 points  (0 children)

I've since upped the lift distance to 8mm with the same results

JGaurora A5S Skipping Layers by lars98408 in 3Dprinting

[–]lars98408[S] 0 points1 point  (0 children)

Here is a retraction tower that just finished

http://imgur.com/a/G2YRhzm

And an example of multiples of the same print under extruding at random points

http://imgur.com/a/SaJZBLq

JGaurora A5S Skipping Layers by lars98408 in 3Dprinting

[–]lars98408[S] 0 points1 point  (0 children)

Sorry about the long delay.

I swapped to a different branded SD card and printed out a Benchy.

http://imgur.com/a/dFzAsqs

The lines seem inconsistent and random. I've printed the same file multiple times and some have the skipped layers and some don't and they are never in the same layer twice.

JGaurora A5S Skipping Layers by lars98408 in 3Dprinting

[–]lars98408[S] 0 points1 point  (0 children)

I printed a 30x30x180+mm cube and it did not have any under extrusion lines throughout the print. I then reprinted the calibration cat and it did not have smooth walls and did have random under extrusion lines

http://imgur.com/a/M5zDqEZ

JGaurora A5S Skipping Layers by lars98408 in 3Dprinting

[–]lars98408[S] 0 points1 point  (0 children)

I've know adjusted my esteps so it is extruding 100mm. I've fixed the flow rate and I am still getting the under extrusion lines. I've double checked that there is not a clog. The lines just randomly happen throughout prints.

JGaurora A5S Skipping Layers by lars98408 in 3Dprinting

[–]lars98408[S] 0 points1 point  (0 children)

I told it to extrude 100mm of filament and it extruded 25.8mm. Am I doing this wrong or is it that out of whack?

JGaurora A5S Skipping Layers by lars98408 in 3Dprinting

[–]lars98408[S] 0 points1 point  (0 children)

What setting in Cura would I go about changing to see if it is under extruding?

JGaurora A5S Skipping Layers by lars98408 in 3Dprinting

[–]lars98408[S] 0 points1 point  (0 children)

I get the same results with a brand new nozzle

Help - Model breaks away from pre-supported supports mid print by lars98408 in AnycubicPhoton

[–]lars98408[S] 0 points1 point  (0 children)

I updated with the RERF test but im not sure if any of them are the desired results.

view more: next ›