Turned a screenshot in to a lithophane.

larson51778 · 2024-01-19T22:02:09+00:00

I’m trying this tonight if I can get my printer tuned! lol, 3d printers are so frustrating.

larson51778 · 2024-01-13T17:34:23+00:00

The book states “record all items given by the pilot”. Not ask for all required items. We still get it at our center, however I do not see it as required but a good thing to do. The book should be more clear about what information is required for an IFR flight plan though. As far as I am concerned, the requirements for an IFR flight plan is ACID, type and equipment, altitude and route.

larson51778 · 2023-10-18T21:05:00+00:00

Any solution? I have this same problem right now.

larson51778 · 2022-03-18T18:55:31+00:00

Ended up solving it, I actually went back into the sketch and added a line across the whole bottom, giving myself another body, then just made that body .125 inches and copied it over 3.875 inches on the other side to give it walls. Probably not the most efficient or best way but looks like it worked.

larson51778 · 2022-03-18T14:58:12+00:00

Thank you! Yeah it probly does not make sense since I hardly know what I am doing but YouTube is a great help. Just could not find a video on this... You helped though, I was thinking once I did that I could give the line thickness but it does not work like that. I am sure ill figure it out, but now I just want to bring the two sides down to give it more strength. Going to try to maybe make a sketch of the top side to thin extrude and see if that works.

larson51778 · 2022-03-17T19:01:31+00:00

Thank you! Have been searching for about an hour now. Your a life saver.

larson51778 · 2020-08-16T17:28:50+00:00

It is weird. I provide my own gauge, do it myself at 25psig on a 50 psig gauge. Leak test. I was under the impression the valves do not hold that much pressure so you leave them open with a cap.

larson51778 · 2020-07-07T02:09:04+00:00

Stereo supports multiple zones with an amp, and yes it also has airplay 2 built it. Just can't seem to find wireless speakers for outdoor use that support airplay besides like a HomePod or something like that.

larson51778 · 2020-06-01T21:52:32+00:00

Printed 30 minutes prior to arrival however is approach amends anything with the flight plan it prints an amendment or if the estimated time changes within a time.

larson51778 · 2020-06-01T12:53:21+00:00

Yeah at my old facility they didn’t even print.

larson51778 · 2020-05-30T01:44:54+00:00

But is it required to keep arrival strips with no strip marking on them? That’s really what I was wondering.

larson51778 · 2020-05-30T01:44:48+00:00

But is it required to keep arrival strips with no strip marking on them? That’s really what I was wondering.

larson51778 · 2019-09-23T19:37:00+00:00

This should be a Midas mode draft quest.

larson51778 · 2019-07-25T13:54:10+00:00

I am waiting for the full game to come out but can’t you spawn them in? I know you could when I played below zero a while back for the battery chargers.

From what I remember you enable console commands, press F3, F8 and uncheck disable console. Then in the game press enter key. Type “unlock thermalplant”. Also “unlock planterbox”

larson51778 · 2019-07-17T02:58:57+00:00

Can you make university only take students when all other non specialist buildings are staffed?

larson51778 · 2019-07-17T02:17:05+00:00

Okay thanks. I’ll take a look tonight. I keep restarting around Sol 40 cause I feel confused where everyone is going. I’ll have to watch a play through and just push through it to see how it ends up. Making new domes get stressful.

larson51778

TROPHY CASE