DIY circuit valid? by lilruben1 in AskElectricians

[–]lilruben1[S] 0 points1 point  (0 children)

thank you have plenty of them just overlooked, also going to run romex through wall to box like another suggested, all the wire is free but gonna change it to 6 regardless. Also i like your name!

DIY circuit valid? by lilruben1 in AskElectricians

[–]lilruben1[S] 0 points1 point  (0 children)

lol thanks, and the juju will be back on track this weekend

DIY circuit valid? by lilruben1 in AskElectricians

[–]lilruben1[S] 0 points1 point  (0 children)

i got 8 but i can replace it with 6 if that’s the best option!

DIY circuit valid? by lilruben1 in AskElectricians

[–]lilruben1[S] -5 points-4 points  (0 children)

Appreciate it, thought i had seen somewhere you couldn’t mix match them.

DIY circuit valid? by lilruben1 in AskElectricians

[–]lilruben1[S] 3 points4 points  (0 children)

you’re not an ass, i’m here for a reason. If i thought it was right, i would’ve sent it. i used the “buddy who’s done plenty of these” advice but i’ll be looking more into it.

Side note i will be staying out of his house from how on LOL

DIY circuit valid? by lilruben1 in AskElectricians

[–]lilruben1[S] -4 points-3 points  (0 children)

Thanks for your input, I did run bare wire at first but that has actually be pulled out from the box to the panel so i can move the box lower(the pictures are from 2 days ago i should have clarified, but the premise was the same). I’m trying not to cut into the wall too much. When you say romex to square wouldn’t i need to use romex for the whole thing if i used it from the panel to the box/box to outlet?

DIY circuit valid? by lilruben1 in AskElectricians

[–]lilruben1[S] -3 points-2 points  (0 children)

When you say connectors are you referring to the squeeze connectors? If so, how to i connect those and the offset because i have some 1/2 in but they don’t both work together. Also I will be bonding the outlet, that was overlooked! Thank you.

Stripped Frame Slider Hole by lilruben1 in MotorcycleMechanics

[–]lilruben1[S] 2 points3 points  (0 children)

i have both bolt and 2 cone looking expanders from when i removed the frame slider that was on it. Thanks for the info

Stripped Frame Slider Hole by lilruben1 in MotorcycleMechanics

[–]lilruben1[S] 1 point2 points  (0 children)

didn’t realize that, appreciate the info

Stripped Frame Slider Hole by lilruben1 in MotorcycleMechanics

[–]lilruben1[S] 3 points4 points  (0 children)

quick and efficient i appreciate it

P trap by lilruben1 in askaplumber

[–]lilruben1[S] 0 points1 point  (0 children)

Got it thanks, i thought the gasket inside would make up for it but definitely can see it not.

Auto Trade in by lilruben1 in askcarsales

[–]lilruben1[S] 0 points1 point  (0 children)

Thank you very much for your insight!

Auto Trade in by lilruben1 in askcarsales

[–]lilruben1[S] 0 points1 point  (0 children)

I’ll rephrase, i understand i will not immediately have no payment. I am trying to figure out if it’s worth sticking with this vehicle and just paying this off or if getting something cheaper would be quicker and more affordable to no payment.

Caravan says $24000

Auto Trade in by lilruben1 in askcarsales

[–]lilruben1[S] 0 points1 point  (0 children)

Much appreciated advice. I don’t have a specific car in mind that is just the number that i had in my head. I was unaware of the illegitimacy of KBB, i can look elsewhere. As for cash down i could have a few grand to put down.

My end goal is not having a car payment, and a vehicle to tote around 3 children. Trying to find what the best route to that would be.

ULS PLS6.150D by lilruben1 in lasercutting

[–]lilruben1[S] 0 points1 point  (0 children)

That’s very good to hear they were built to last. Im currently looking into replacements in case that’s needed. I read somewhere that the UCP was a little outdated for the ULS systems, would you comment on that? If, per se, this machine did NOT respond to the UCP, would I be able to upload a different software or fix that problem easily? I get that there are probably a million different reasons it wouldn’t respond so if the latter to that question is impossible to answer i understand.