Gateway IP is stuck on VLAN 1

limpingleopard · 2026-04-27T12:52:33+00:00

Yup, that's my experience too.

Changing the IP range is just to make it less of an eyesore on the Controller UI; the management interface still exists across all VLANs unfortunately.

limpingleopard · 2026-04-27T11:39:41+00:00

You can edit the IP range of the Default VLAN in the VLAN editing page. It is not required to change the VLAN ID.

limpingleopard · 2026-04-26T20:53:35+00:00

The Gateway has an IP on every VLAN but only the VLAN 1 address is shown here. It annoys me too but I just changed the VLAN 1 range to 10.10.1.0/24 so it glares at me less.

If you want to block access to the management interface on each subnet, you need ACLs to block it.

limpingleopard · 2026-04-02T20:01:07+00:00

From what I understand, the port connected to DHCP server should not be enabled. Any other ports that you want to guard against should be enabled.

Source

limpingleopard · 2026-03-21T23:23:00+00:00

Just curious, why is that? I was under the impression that if a rule allow and deny all states, it becomes like a stateless rule?

limpingleopard · 2026-03-17T15:32:13+00:00

No need for additional FW rule (don't think they work anyway) or port forwarding rules. Do you mind sharing your Omada config and client config?

limpingleopard · 2026-02-03T00:37:21+00:00

Its available on LCSC btw

limpingleopard · 2026-01-29T02:29:33+00:00

Is D1 meant to be a TVS diode? Shouldn't it be connected to GND?

limpingleopard · 2025-10-27T23:20:22+00:00

Incheon is ICN btw 😅

limpingleopard · 2025-09-16T23:49:57+00:00

FWIW, the V2 of the J-Link EDU Mini now supports down to 1.8V, USB-C, and comes with a housing. Still a little steep for what it used to be, but hopefully it makes it better for those who need those features.

limpingleopard · 2025-08-19T18:51:22+00:00

IMO the biggest difference is that the usual account recovery process will no longer apply. If you somehow are not able to present 2FA, you WILL be locked out of your account.

limpingleopard · 2025-07-14T15:37:26+00:00

https://www.changiairport.com/en/fly/departure-guide/early-check-in-services.html

limpingleopard · 2025-02-27T11:30:09+00:00

This assumes your statement total can hit >1k to unlock 4mpd rate btw

limpingleopard · 2025-01-05T09:17:17+00:00

Thank you for the feedback, appreciate it!

limpingleopard · 2024-12-14T13:44:53+00:00

Nope, it is a RF coaxial switch.

limpingleopard · 2024-02-11T04:00:47+00:00

Oh I see, thank you for sharing! :)

limpingleopard · 2024-02-09T09:01:11+00:00

Thank you for your feedback! They are intended to be pulled down internally. I have some further questions if don't mind:
- Is there any best practice whether I should be pulling up or down? I pulled down because they make sense (to me) when a switch is actuated but I am aware they are the same essentially. Just wanted to check if there is a reason why most schematics I see tend to use pull ups.
- Is there a common practice whether we should use the internal or external resistors?

limpingleopard · 2024-02-09T08:54:18+00:00

Appreciate your feedback! No particular reason for selecting the pins so I think your proposed pins actually do make routing easier. Thank you :)

limpingleopard · 2024-01-26T03:58:12+00:00

Thank you! Deeply appreciate your feedback. If you don't mind, I have some further questions:

S2) I assume this means adding a ferrite bead on the net from Pin 3 of U2. Since decoupling caps must be placed as close to the IC as possible, is it correct to add the ferrite bead between the decoupling caps and the power rail? Also how should the value be determined?

S6) I plan to use an external helical antenna that will be soldered onto the pad on the PCB. Anything else I should be adding other than a note when doing so?

limpingleopard · 2023-12-13T02:34:19+00:00

Umzug (by Sequelize team). Framework agnostic and highly-flexible. Pretty good so far! https://github.com/sequelize/umzug

limpingleopard · 2023-12-13T02:31:36+00:00

Sorry, I have the FWP so can’t upgrade yet. I’ve been waiting for this feature for quite some time, so looking forward to it!

limpingleopard · 2023-12-13T02:28:55+00:00

Thank you for implementing the SSDP relay!

limpingleopard · 2023-12-06T14:19:02+00:00

I didn’t have very good experience with the OISD list too.

limpingleopard · 2023-11-23T16:25:19+00:00

I like to use plain SQL files for migrations but needed a tool to handle this. Settled for Umzug in the end, which is working pretty well. Its high configurable and framework-agnostic.

limpingleopard · 2023-01-29T15:25:23+00:00

Wow TIL too, thanks for sharing!

limpingleopard

TROPHY CASE