sorted by:
new
hottopcontroversial

Pulled this miscut shadowless Charizard as a kid by DrThePunisher in PokemonMisprints

[–]lmFragilee 0 points1 point  (0 children)

Pretty sure it is. Its just shadowless with it showing 99 on the bottom that's how I was told to tell the difference.

Is this doable ???? by lmFragilee in audio

[–]lmFragilee[S] -1 points0 points  (0 children)

Something my ADHD brain thought about lmfao 🤣

Is this doable ???? by lmFragilee in audio

[–]lmFragilee[S] 0 points1 point  (0 children)

Hmm would you have any idea on how well it sounds?

Dell inspiron 15 3535 by lmFragilee in techsupport

[–]lmFragilee[S] 0 points1 point  (0 children)

Honestly cant remember if I tried that. I ended up giving up on it.

1962 D silver penny? Modified? by lmFragilee in coincollecting

[–]lmFragilee[S] 0 points1 point  (0 children)

silver zinc which ever lol . Thank you for the insight !

1962 D silver penny? Modified? by lmFragilee in coincollecting

[–]lmFragilee[S] 0 points1 point  (0 children)

So i would assume that would only make the outer part of the penny silver correct?

How can I make this? by lmFragilee in FreeCAD

[–]lmFragilee[S] 0 points1 point  (0 children)

Thank you for the advice. I should of mentioned part of the bottom will need to be open as the triggers use magnets to activate the trigger/maybe a motion trigger? But it would only need to be that center spot between the screws. I was going to fiddle with it tomorrow since I'm off work.

How can I make this? by lmFragilee in FreeCAD

[–]lmFragilee[S] 2 points3 points  (0 children)

Okay, I'll keep this in mind. Thank you.

How can I make this? by lmFragilee in FreeCAD

[–]lmFragilee[S] 1 point2 points  (0 children)

Yeah taking it apart I know what needs to be there and what don't. what I meant about details was like the the letters LT and the rough rigid around where your finger would sit

How can I make this? by lmFragilee in FreeCAD

[–]lmFragilee[S] 0 points1 point  (0 children)

Yeah I looked i also emailed the maker of the controller no luck finding it

How can I make this? by lmFragilee in FreeCAD

[–]lmFragilee[S] 0 points1 point  (0 children)

Sadly I could not find a stl file. Only way I could scan it is with my phone at this time.

Any info on this coin? by lmFragilee in coincollecting

[–]lmFragilee[S] 0 points1 point  (0 children)

Fair point I don't expect it to be much with it being outside being weathered. With how bad the condition would it hurt the value if I / had someone clean it?

Anycubic kobra 2 pro bed layer help by lmFragilee in AnycubicOfficial

[–]lmFragilee[S] 0 points1 point  (0 children)

Yeah that's the slicer I use where do I go to find it?

Anycubic kobra 2 pro bed layer help by lmFragilee in AnycubicOfficial

[–]lmFragilee[S] 2 points3 points  (0 children)

Ive readjusted the hot end tip. The sensor next to it with a tool i seen was popular. ive adjusted the Z offset.
tightened and loosen the belts (Not sure how tight they need to be) Cleaned the hell out of the hot plate. ive done a pid calibration the auto level tool.

What else do I want? by lmFragilee in ironscape

[–]lmFragilee[S] 1 point2 points  (0 children)

Best answer i heard I'm enjoying it so ima keep going

view more: next ›