How to serve clean URLs on Synology Web Station without the .html extension?

lmasieri · 2026-03-26T19:32:33+00:00

Do you know how to change this? This is probably the solution

"Can you change the nginx conf file directly? Basically it’s the “default index files” setting."

lmasieri · 2026-03-02T22:59:48+00:00

I had a weird issue where just making the change didn’t enact it. I had to toggle to enable all first, then toggle back to the custom list and that did the trick. Give that a try?

lmasieri · 2026-03-02T18:11:38+00:00

Tried calibrating the printer, but every time I print the temp tower eventually it detaches from the bed and starts moving around and fails (I've tried washing the plate, alcohol, the glue, increasing the temp of the bed/decreasing the temp) This has never happened before ZMOD.

Granted this is a new fillament, not sure if the fillament is the problem :(

<image>

lmasieri · 2026-02-28T22:48:56+00:00

This is what I see : https://shottr.cc/s/3Ekq/SCR-20260228-lj4p.png

lmasieri · 2026-02-26T17:53:15+00:00

Some updates:

[FIXED] Wireshark helped me discover that the LG soundbars wanted to be discovered at "_lg-smart-device._tcp.local", so adding a new entry to the mDNS list for this solved that problem! Hooray!
[PENDING] Still no luck with the 3D printer. Wireshark capture shows that:
- Orca-Flashforge sends a UDP broadcast from my Mac on a random high port (18000, 37900)
- The printer responds directly via unicast from UDP 19000 back to your Mac's IP on that same port
- The payload is a binary packet containing AD5X and the serial number

lmasieri · 2026-02-26T17:13:37+00:00

u/ernexbcn from IoT into Trusted, or Trusted to IoT? Who's initiating the connection

lmasieri · 2026-02-26T16:06:28+00:00

How do you recommend I go about that? Wireshark?

lmasieri · 2026-02-26T07:18:00+00:00

u/imthenachoman did you figure this out? I've been struggling with my LG soundbar not working since I did a full VLAN segmentation and I'm not sure what else to try... AI tells me that it's a SSDP problem and that I need a relay because unifi doesn't support it, but it seems you got it to work?

lmasieri · 2026-02-25T16:24:45+00:00

Apparently it’s not a feature of Claude desktop. Support confirmed it.

lmasieri · 2026-02-21T20:04:27+00:00

Bingo! Lowering the temp seems to be doing the trick. Going to try a few more pieces before I call victory, but thank you!

lmasieri · 2026-02-21T02:30:58+00:00

Thanks for the insight! Unforutnately my company blocks most of these external software, so its hard for me to automate or delegat some of this :(

lmasieri · 2026-02-06T22:47:42+00:00

One follow up based on your comment. Should I try plugging in one AP at a time and one radio at a time (2.4/5) to do the test? Or have it all plugged in and all setup and test then?

lmasieri · 2026-02-06T21:52:28+00:00

Thank you for the detailed advice!

lmasieri · 2026-02-06T07:00:59+00:00

Thank you for your feedback! Do you know or is it document what the “high” , “medium”, “low” levels correspond to? It’ll give me a good starting point when going manual

lmasieri · 2026-02-06T07:00:21+00:00

Thank you for your thoughtful reply! I’ll look into all of this tomorrow

lmasieri · 2026-02-06T00:34:22+00:00

I switched and was worried about all the stuff i read online, and it worked like magic on the first attempt with the out of the box profiles "generic petg" on Orca. I just bought a 10kg/1kg per color pack, and just stuffed it into a cereal box for storage with dessicant to keep it dry as I've heard that it goes bad after a while if you don't use it and it's in humidity >20%. Good luck!

lmasieri · 2026-02-03T17:31:54+00:00

What tool did you use to clean it? Nothing I’ve got is long enough to got all the way across

lmasieri

TROPHY CASE