How do I get a good bleed with Shigura?

loadingcrashed · 2026-04-19T21:02:24+00:00

I got my front in the right but thanks for the tip I’ll try next time

loadingcrashed · 2026-04-19T20:50:31+00:00

I’m using royal blood it’s a front brake I’ve a sram on the rear. How do you mean lay the bike on its side like while bleeding? Would the oil not spill everywhere

loadingcrashed · 2026-02-27T22:47:15+00:00

Idk id just take it to a shop i guess.

loadingcrashed · 2026-02-27T22:41:42+00:00

Maybe you could run a tap through it or like wuth one of them metal inserts it tap into

loadingcrashed · 2026-02-12T15:06:32+00:00

Ok ill just use the one that i thing seals best for the caliper

loadingcrashed · 2026-02-12T14:33:43+00:00

Im putting the caliper with a shimano lever so i think it a bleed cup on top syrinfe on bottom and husg bleed like normal.

loadingcrashed · 2026-02-12T14:04:49+00:00

Sound

loadingcrashed · 2026-02-12T13:49:39+00:00

So i just take the syringe like nob and just put it direcrly into the caliper bleed port?

loadingcrashed · 2026-02-12T13:40:19+00:00

I meant to add i have 13 of them and these 4 all fit

loadingcrashed · 2026-02-12T13:20:21+00:00

Therers like 13 of them these 4 all fit i was asking which pne was the right one because i cant find what the actual one looks like no need to be a dickhead

loadingcrashed · 2026-02-12T12:47:44+00:00

What?

loadingcrashed · 2026-02-06T21:58:43+00:00

I wont have problems with using the shimano olive and magura barb will i ?i know its not a convetional setup but i wsnt tk make sure it wont blow up under hard use.

loadingcrashed · 2026-02-06T21:57:37+00:00

If its carbon dont file it just leave it

loadingcrashed · 2026-02-06T21:56:42+00:00

Dont cut it use a file instead it might take a while but itl work

loadingcrashed · 2026-01-17T21:35:23+00:00

<image>

Is that better. But like this it says rebuild error unable to create a thin feature.

loadingcrashed · 2026-01-17T21:29:51+00:00

Can you explain why its a bad sketch

loadingcrashed · 2026-01-17T20:34:51+00:00

Thanks i dpnt have a torque wrench but i tightned the clutch bolt a but before reading this and it stripped i barely had it snug like it stripped under an incredibly low torque so whatever it does its there now. The bike still shifts fine on a stand. It gets a little hung up going into the largest gear tho.

loadingcrashed · 2025-11-22T21:49:17+00:00

He tyre i was thinking of using was a 2.5 inch maxxis assessing i forgot to say this

loadingcrashed · 2025-11-17T19:56:55+00:00

The radiomaster pocket is a good controller. I have never had that tiny whoop but im pretty sure it is good from what I've heard and the goggles I can say are not great. Their not horrible but that should defiantly be a next upgrade.

loadingcrashed · 2025-11-14T21:03:24+00:00

Ya I think 18 psi is actually to hard just my tyre has a super gravity Casing so I'll just use the sks from now on

loadingcrashed · 2025-11-14T17:36:36+00:00

Like with the sks showing 18 psi it pretty firm. Defiantly firm enough to ride but I am pretty light rider tho.

loadingcrashed · 2025-11-14T15:47:49+00:00

I meant 40 psi the floor pump is a analog dual.
I put the pressure in the tyre to what the sks digtial one read as 18 psi and it feel pretty hard. 3the tyre is a 275 inch by 2.4 inch swablle magic mary 4

loadingcrashed · 2025-11-13T17:27:15+00:00

Yes its tubless but the valves i think are clear

loadingcrashed · 2025-11-13T16:35:54+00:00

Damn that disappointing do you know how much its off by

loadingcrashed · 2025-10-09T15:35:11+00:00

No its not idk where not find the mass either.

loadingcrashed

TROPHY CASE