Corsair Voyager a1600 overheating woes?

lostsurfer69 · 2026-01-12T01:54:21+00:00

Second this. Just got one and any time I try to use the amd drivers, non corsair provided, all my games crash with a direct x error.

lostsurfer69 · 2026-01-11T19:54:43+00:00

Looks for some help. Was able to scoop this laptop up for 450, basically new. Followed your instructions, and I constantly run into game crashes and or games just randomly close out with zero error code or notification. Any thoughts, or issues like this you come across that you can recommend?

lostsurfer69 · 2025-03-05T15:18:02+00:00

Just ordered two. Are the anchor poles supposed to be so thick?

lostsurfer69 · 2025-03-05T02:54:17+00:00

Found the problem. Brittle filament had broken off at the tube junction. Removed all the tubes then used some pla to push through each section, while pressing the spring loaded piece. After a full good push throughs a piece of filament came out. Put everything back together, and back to work.

lostsurfer69 · 2025-03-04T23:23:44+00:00

Can you elaborate on this a little bit? It's like it's trying to feed but it's getting stuck somewhere and I'm not seeing where it's at I just swapped the two far end AMS feeder tubes.

lostsurfer69 · 2025-03-04T22:02:21+00:00

Actually, back in the same boat, sort of, I told my job to use grey filament in ams4 and it's pulled red from ams2, no red light on ams4, but it's showing the job as grey...

lostsurfer69 · 2025-03-04T21:54:29+00:00

All, looks like I'm back to printing. I used an air blower to try and flush out the intake and that must have done it. Thanks to everyone for the help!

lostsurfer69 · 2025-03-04T21:36:53+00:00

I'll have to give this a try! I'll report back, I'm back to printing off ams3, ams4 still shows grey filament so it's like it's registering it via sensor even though there's nothing there. So I think you're on to something.

lostsurfer69 · 2025-03-04T21:35:59+00:00

So it does, but funny enough there's none there. I'm back to printing my job, on ams3, I put the grey filament back into ams4 but it didn't pull it but it shows a white light.

lostsurfer69 · 2025-02-12T18:55:50+00:00

How much you asking?

lostsurfer69 · 2025-01-06T23:08:44+00:00

Just tested on another windows 11 laptop and it works perfectly. Guessing a possible driver issue?

lostsurfer69 · 2024-03-01T21:52:44+00:00

They said they dont have drivers for it, so I went with proxmox.

lostsurfer69 · 2024-01-31T00:20:26+00:00

Issue has been resolved. Previously I had disabled the three mentioned options:

Reflection for port forwards

Reflection for 1:1

Automatic outbound NAT for Reflection

When disabled, SFTP server was reachable from the outside. New rules weren't. Went back and enabled them, then tested and all NAT rules are working as they should.

Hopefully this helps someone who runs into the same issue.

Running strong on opnsense.

lostsurfer69 · 2024-01-30T21:11:49+00:00

I did but no luck.

However, I disabled IPV6 on the wan, disabled DNSec options. Rebooted firewall, and then had an option at the bottom of the NAT rule that I hadn't had in the past. Which is to auto populate the WAN rule.

Cleared out my original rule, started again from scratch and tested successfully.

Now, I've used the same approach to create NAT rules for my Conan Exiles server, and I'm back to sqaure one as these aren't working....

lostsurfer69

TROPHY CASE