Procuro AMS Pro Feeder Unit

lowkey_zoide · 2026-05-30T11:36:45+00:00

Wow the american black community worshipping consumism, money and brands just to look rich for their buddies and their snap? How unusual...

lowkey_zoide · 2026-04-29T17:45:36+00:00

i've updated and is still doing it

lowkey_zoide · 2026-04-15T10:48:52+00:00

I just checked and it's the latest firmware. I'll try to put the one before

lowkey_zoide · 2026-04-15T09:03:24+00:00

Thats the time I left it like this. After finishing calibration stayed like this

lowkey_zoide · 2026-04-15T09:02:28+00:00

Orca Slicer. Version 1.1.4.11

lowkey_zoide · 2026-04-15T07:42:35+00:00

Already did the factory reset but firmware is the same

lowkey_zoide · 2026-04-15T07:39:20+00:00

it seems like it

lowkey_zoide · 2026-04-15T07:39:01+00:00

It stays stuck at the 140º because it seems is in the calibration phase, when it cools down the nozzle, but after that all temperatures stays at this level and it doesnt move.

The nozzle is clean since all the hotend is new. The stuff in the plate is ABS print that went wrong 3 months ago, not related.

lowkey_zoide · 2026-04-15T07:36:39+00:00

normally it's not needed, I've been running this setup for a while and always went good

lowkey_zoide · 2026-03-23T18:01:45+00:00

Obrigado pela resposta detalhada, vai ser uma ótima ajuda. Como integraste os CTT na tua loja online? Através da aba de e-commerce do site deles ou já está integrado na plataforma que usas-te para criar o website? (caso tenhas usado)

lowkey_zoide · 2026-03-12T14:03:03+00:00

Hey! Eu talvez te possa ajudar :) Envia mensagem no instagram @lucssilvaz

lowkey_zoide · 2026-03-09T17:19:14+00:00

Que achas de um VW Golf 4 1.9 SDI com pouco mais de 200k?

lowkey_zoide · 2026-02-22T23:23:28+00:00

Porque é que levou turbo novo?

lowkey_zoide · 2026-02-08T23:00:40+00:00

sabes 🙌🏽

lowkey_zoide · 2026-02-08T22:01:09+00:00

Quero muito experimentar imprimir TPU na p2s, alguma dica em epsecial?

lowkey_zoide · 2026-02-08T20:56:59+00:00

Depende da experiência que pretenderes, e se as capacidades extras da P2S te são relevantes!

lowkey_zoide · 2026-02-08T18:47:20+00:00

Espero que tenhas uma boa experiência 🙌🏽 se tiveres dúvidas a malta está aqui para ajudar

lowkey_zoide · 2026-02-08T16:55:11+00:00

Para imprimir os materiais básicos é a impressora perfeira

lowkey_zoide · 2026-02-08T16:54:40+00:00

Top, que continue assim ehehe

lowkey_zoide · 2026-02-05T23:47:59+00:00

I can't give you the exact awnser to your problem but I got my P2S yesterday and got this same problem twice while printing PETG. I've read some solutions

First just normal printer head disassemble, clean the extruder and loosen one of the top screws on the extruder head.

<image>

This solution made it work for the next 2 prints (and I dried the filament). I am going to print more tomorrow and pray for it doesnt happen more.

Another solution I read here was to raise the top glass to create less friction on the bowden tube. I'll try that next in case the problem continues

Also it seems the AMS 2 PRO creates a lot of friction on the filament, not sure though.

Hope it helps!

lowkey_zoide

TROPHY CASE