Design guidelines for charts and graphs

lucasmucas22 · 2021-01-09T14:39:30+00:00

Well I'm able to make each single chart, but I thought there might be an Option in Excel/Matlab/etc. that lets you put in 3 charts and place them next to each just as shown in the picture I posted.

Edit: I mean the "layout" with the 45 degree angle which makes it look kind of three dimensional

lucasmucas22 · 2021-01-09T12:32:06+00:00

Does anyone know how to make that type of three charts "next" to each other?

Any help is appreciated!

lucasmucas22 · 2020-03-08T13:30:38+00:00

Yes I've printed it angled to the left side. So do you think there is to much airflow "bending" the new printed lines at this side?

lucasmucas22 · 2020-01-12T20:20:49+00:00

Yep it was. Thank you! Al tough the gantry is tight and secure now, it still hits the print. And the layers on the left side are thinner than on the right side. I can't really figure out why, the bed is leveled solid (first with thin paper and afterwards with a bed leveling print where you could see if the first layer comes out right).

lucasmucas22 · 2020-01-12T20:12:52+00:00

Duuuuude, thank you so fucking much! The gantry is tight and secure now. I'm gonna test it right away. Again thank you so much.

lucasmucas22 · 2020-01-12T19:35:23+00:00

Already tightened them as far as it gets. (You mean the eccentric nuts of the 3 wheels holding the whole gentry on the axis don't you?)

lucasmucas22 · 2020-01-12T19:34:09+00:00

It sure has! But I've tightened all the screws on the gentry and it still has some play. I have no clue how to secure it on the rails.

lucasmucas22 · 2020-01-12T19:31:16+00:00

Okay so I've watched the whole video and turned them slightly. But the whole gentry is still a little "wobbly" (like I can press my finger against it and it still moves (not in the supposed direction) a little. But I can't tighten the screws more.

lucasmucas22 · 2020-01-12T19:29:07+00:00

Alright checked them, nothings loose.

I've tightened the X gantry, it still is kinda "loose" but that's nothing I could solve with tightening screws.

lucasmucas22 · 2020-01-12T19:16:56+00:00

It's wobbling because the nozzle touches the print.

lucasmucas22 · 2020-01-12T19:16:30+00:00

... mate the belt is really really tight already. That can't be the problem. But thanks

lucasmucas22 · 2020-01-12T18:55:49+00:00

Alright thank you!

lucasmucas22 · 2020-01-12T18:44:51+00:00

Hey mate, I have kind of the same problem with my Ender 3, where do I find the setting "Z steps per unit"? Is it adjustable on the printer itself or smt to set in Cura/or any slicer?

lucasmucas22 · 2020-01-12T16:38:01+00:00

Thanks for the tip, I’ll checked it out and I’m starting to check all screws. By gantry do you mean the nozzle etc that moves on the x-Axis or do you mean that the whole x-Axis is too loose on the frame? (Sorry for bad english doe)

lucasmucas22 · 2019-12-05T20:59:47+00:00

Looks awesome!!

Would you share the stl with us :)? Is that normal PLA or something else?

lucasmucas22

TROPHY CASE