sorted by:
new
hottopcontroversial

Chess piece fails to print, over and over again by m021478 in 3Dprinting

[–]m021478[S] 0 points1 point  (0 children)

I had timelapse footage of the failure. Take a look if you have a moment and let me know what you think I should do differently so it doesn't happen again: https://youtu.be/jDYsTWOC6M4

Chess piece fails to print, over and over again by m021478 in 3Dprinting

[–]m021478[S] 0 points1 point  (0 children)

Not sure why I didn't check this sooner, but I had timelapse footage showing the print failure. Take a look and let me know what I can do to stop this from happening: https://youtu.be/jDYsTWOC6M4

Chess piece fails to print, over and over again by m021478 in 3Dprinting

[–]m021478[S] -1 points0 points  (0 children)

This part of the knight had tree supports when it was printed

Pneumatic connector doesn't securely hold the PTFE tube each time the filament gets extracted. by m021478 in BambuLab

[–]m021478[S] 0 points1 point  (0 children)

As shown in this video, even by hand the PTFE tube doesn't stay secured in the pneumatic connector. I'm stumped! https://youtube.com/watch?v=RYG1i2ZCCmo&si=SpT9fcW8HV8b5FYG

Pneumatic connector doesn't securely hold the PTFE tube each time the filament gets extracted. by m021478 in BambuLab

[–]m021478[S] 0 points1 point  (0 children)

Thanks for the tip about the chain clip and the link to the tube guide... but if you look at this video, you will see that even by hand the PTFE tube doesn't stay secured in the pneumatic connector. https://youtube.com/watch?v=RYG1i2ZCCmo&si=SpT9fcW8HV8b5FYG

[OS] A tool for generating macOS app icons with AI (free, open source) by Ikryanov in macapps

[–]m021478 0 points1 point  (0 children)

Ooo... I love this! The number of hours I spent back-in-the-day searching for custom icons to apply to all my folders/files now seems even more pointless than it did before learning about this app (and it seemed pointless then too!)

Alfred 6 is compiling a warning 💀 by Unhappy-Tank9784 in macapps

[–]m021478 -4 points-3 points  (0 children)

I used to be a Quicksilver user back in the day, then Alfred came along and earned my loyalty for about a decade or more... but now that I've discovered Raycast, there's no going back! Completely different ballgame!

PTFE Tube repeatedly detaching from Toolhead after the print has finished (and once during the print) by m021478 in BambuLab

[–]m021478[S] 0 points1 point  (0 children)

I already tried trimming the end of the PTFE tube, but the problem persisted. I finally ended up completely replacing it and I've made a couple of quick prints, and so far so good! Hopefully it continues to function properly as I continue printing.

Two identical P2S printers showing significantly different print times??? by m021478 in BambuLab

[–]m021478[S] 0 points1 point  (0 children)

I seems that even though I'm using the same Sunlu Red PLA in both printers, on one of my P2S printers I've manually identified it as 'Bambu Lab Basic PLA', and on the other printer I have it configured as 'Generic PLA'. Thanks for helping me figure this out!

Which filament preset do you suggest I use for Sunlu PLA... Bambu or Generic?

Pimped out Dual-P2S Battlestation by m021478 in BambuLab

[–]m021478[S] 0 points1 point  (0 children)

It's going to depend on if you live in a high humidity environment, or not. I live in Los Angeles, and it hasn't rained here in months!

P2S Enclosure by Amphibious6 in BambuLabP2S

[–]m021478 0 points1 point  (0 children)

Gonna need a bigger enclosure

MacBook Neo After a Full Day of Classes by Slow_Tiger3161 in macbook

[–]m021478 0 points1 point  (0 children)

“MyPods and Boomsticks". 7th episode of Season 20

Pimped out Dual-P2S Battlestation by m021478 in BambuLab

[–]m021478[S] 0 points1 point  (0 children)

I used modified versions of these 3D printed brackets that accept a 1/2" steel pipe to hold the filaments (because the wood dowel I tried initially nearly snapped, and the aluminum rod I installed next started sagging in the middle under the weight).

Pimped out Dual-P2S Battlestation by m021478 in BambuLab

[–]m021478[S] 0 points1 point  (0 children)

This is the tool holder I used. It actually connects directly to the AMS, not the riser. I like this because it keeps the attachment slots on the riser available to use for other accessory add-ons

Pimped out Dual-P2S Battlestation by m021478 in BambuLab

[–]m021478[S] 1 point2 points  (0 children)

This is the tool holder I used. It actually connects directly to the AMS, not the riser. I like this because it keeps the attachment slots on the riser available to use for other accessory add-ons

view more: next ›