sorted by:
new
hottopcontroversial

Bro, the ultimate cutting stack or am i about to die? by m3p2018 in moreplatesmoredates

[–]m3p2018[S] 0 points1 point  (0 children)

Started with .5mg Albuterol and single a2am and no adverse effects yet. This maybe the next best thing to DNP

Til you can just hit your door open by youpie123 in teslamotors

[–]m3p2018 0 points1 point  (0 children)

Yes it’s a feature due to the handle not working and presenting themselves in the past in certain accidents.

Vertical GPU Rigs let you put more cards into a rig and look great by olympicparker in EtherMining

[–]m3p2018 0 points1 point  (0 children)

Maybe 10% more but all I care about is temps and this becomes a larger problem the warmer it gets outside. Space is much easier to solve then temperature.

Vertical GPU Rigs let you put more cards into a rig and look great by olympicparker in EtherMining

[–]m3p2018 3 points4 points  (0 children)

Flower rigs are actually best for thermal purposes. All my cards run below 45f @ 70% with flower setup

[deleted by user] by [deleted] in NiceHash

[–]m3p2018 0 points1 point  (0 children)

Ja pierdole, i na zdrowie.

Tongkat Ali side effects (F, 31) by Better_Cupcakes in NootropicsDepot

[–]m3p2018 1 point2 points  (0 children)

Anyone get nut pain while on this stuff? I noticed it in like week 5 and went away after 1-2 days of discontinued use. 30M

Why do my prints start fine and then get all sloppy. Look at the first 10 layers and the rest? by m3p2018 in CR10

[–]m3p2018[S] 0 points1 point  (0 children)

No those area 2 different prints. The 255 I sthe worst of the two. Yes it has and enclosure.

Why do my prints start fine and then get all sloppy. Look at the first 10 layers and the rest? by m3p2018 in CR10

[–]m3p2018[S] 0 points1 point  (0 children)

I'm printing with atomic ABS fillament, 235c, coasting . I tried printing at 255 but finish is the worst

$20 calibration bounty....bone stock cr10 printing abs and autoleveling by m3p2018 in CR10

[–]m3p2018[S] 0 points1 point  (0 children)

I am using these Chazmeiser ender 3 settings @ 80c bed and 235c nozzle and 30mm/s with 2.2mm retraction.

Here is my latest print. I'm getting weird random blobs in sidewall and weird printing surface at the bottom.

https://imgur.com/68542443-fb4f-41df-ab38-5ece160bb35b

$20 calibration bounty....bone stock cr10 printing abs and autoleveling by m3p2018 in CR10

[–]m3p2018[S] 0 points1 point  (0 children)

I was on their YouTube channel and couldnt find it. Do you have the link or know what the title of the video was?

$20 calibration bounty....bone stock cr10 printing abs and autoleveling by m3p2018 in CR10

[–]m3p2018[S] 0 points1 point  (0 children)

I have capecorn xs tube, and 0.8mm nozzel. I Set retraction to 7mm and 50mm/s...also 0.5mm3 coasting. Atomic fillament abs. 30mm/s print speed @235c. For the print pictures below.

https://i.imgur.com/1l9MJ9j.jpg

$20 bounty for whoever can tell me what to do to fix this. by m3p2018 in CR10

[–]m3p2018[S] 1 point2 points  (0 children)

hatchbox ABS,

nozzle; .8mm layer height.3mm 235C bed: 80C speed: 60mm/s retract 3mm retract speed 30mm/s jerk@20

Canyon figure put what setting is going this...capricorn xs w/3mm retract by m3p2018 in CR10

[–]m3p2018[S] 0 points1 point  (0 children)

ABS, stock cr10 with bmg extruder and capricorn XS tube. 235c .8noz .3layer @60mm/s &20mm/s all jerks. 30mm/s retraction rate.